Will Hellwig EZ-990 part # HE67FR Add Height to Truck Suspension

Question

Question:

Do these apply any lift to the rear of the truck?

asked by: Jeremiah

0

Expert Reply:

Hey Jeremiah, the Hellwig EZ-990 part # HE67FR can add height if you tighten them down enough. Basically how tight you go with the U-bolts will raise the suspension between 0 and 2 inches.

expert reply by: Jameson C

0

Jameson C.

1/27/2026

Hey Jeremiah, how did things turn out after tightening the Hellwig EZ-990 helper springs on your truck? Did you notice the rear lifting within that 0 to 2-inch range? Your update could make it easier for others setting up the same springs.

Answer 1

Yes, you can run both of your trailer's brown wires to the single brown wire of your new 5-way. Typically this is how most 5-ways are wired. Your old one was a wishbone style connector which means it has the two wires already for that circuit.

view full answer...

Answer 2

G, Yes both the Hellwig EZ-990 Helper Springs #HE67FR and the SumoSprings Solo Custom Helper Springs #SSR-117-47 can be used together. The SumoSprings will replace the factory bump stops, and the Hellwig bolts above the factory leaf springs so the…

view full answer...

Answer 3

The Valterra Waste Valve part #T1001B is the correct replacement for what you have. It is a 1-1/2 inch waste valve with 2 inch hubs that are designed to fit over 1-1/2 inch RV sewer pipe like you have.

view full answer...

Answer 4

I spoke with the folks at RoadActive Suspension and was told that because the RAS system sits within the footprint of the leaf springs, it will not interfere with the sensors for the Auto Headlight feature, but you will need to move the adjustable…

view full answer...

Answer 5

Hey Chuck, that is a good question but yes the mounting holes for a sway bar are present on your 2021 Ram Promaster to allow you to install the Hellwig part #HE74YR that you referenced. What's the handling like now without a rear bar?

view full answer...

Answer 6

The K-Source Snap & Zap Custom Towing Mirrors part #KS81850 are snap on side mirror extensions whereas the CIPA Custom Towing Mirrors part #CM11550 are slip on. The difference between the snap and slip options are as follows: The snap on mirrors…

view full answer...

Answer 7

Hi Erik, The Hellwig EZ-990 Helper Springs part #HE67FR do fit your 2021 Ford F-150, however, there are certain features that if present determine whether or not the springs would fit. These helper springs are designed for trucks with 3 leaf springs,…

view full answer...

Answer 8

Hey Jim, The Hellwig EZ-990 Helper Springs part #HE62FR is not a fit for a 1994 Ford F-150 based on Hellwig's fitment guide on their website. They fit older GM and Chevy trucks but not your vehicle. The Hellwig EZ-990 Helper Springs part #HE48VR…

view full answer...

Answer 9

Hello Mark, thanks for reaching out. The Hellwig Load Pro 35 Heavy Duty Helper Springs with Custom Mounting Kit #HE37TR is the correct fit for the 2010 Ford Van/E350. These will help beef up the factory springs and minimize sagging. They are not…

view full answer...

Answer 10

In order to find the correct replacement axle you have a few options. The first option would be to simply measure the axle you have now and record both the spring center and hub face measurements. The other option would be to look at the axle tag and…

view full answer...

Answer 11

The Timbren Suspension Enhancement System - Rear Axle #TFRTT1504E once the brackets are installed on the top and bottom and with the integrated spacer will give you 1-1/2 inch of clearance between the jounce spring and bracket compared to the 4-1/2…

view full answer...

Will Hellwig EZ-990 part # HE67FR Add Height to Truck Suspension

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching