Replacement Control Panel For An Atwood GC10A-3E RV Water Heater

Question

Question:

Will this control panel work with an Atwood gc10a-3e or is there another control panel that will? The gc10a-3e is a 10 gallon gas/electric version. I see model numbers that are close, but not exact.

asked by: Charles R

0

Expert Reply:

Hi Charles,

The part diagram I can find for the Atwood GC10A-3E shows 91367 so the # AT91367 would be the correct replacement for your water heater's control panel.

expert reply by: Kevin C

0

Charles R.

8/16/2024

Thank you Kevin. Order placed.

Answer 1

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 2

Yes, the CE Smith Trailer Hub part #CE13511 will fit as a replacement for your DICO hub 45264 but you will need to use a different seal as we have found that your spindle diameter is slightly different which means you need the #168255TB as well.

view full answer...

Answer 3

I can't find anything regarding a water heater number 62659 or MPD 91818, and you'll have to know your water heater's model number. The Replacement 4-Wire Control Harness #AT93312 connects to the Control Panel #AT91367, and the pair fits…

view full answer...

Answer 4

I was able to find out from Dometic, who took over Atwood's water heater division and the Replacement Control Panel #AT91367 you were looking at will be the correct part.

view full answer...

Answer 5

I went ahead and reached out to Dometic (the makers of Atwood), and they said that they do not recognize the circuit board with a model number of 93257. However, we do carry the gas-only control panel. That is part #AT91367. This particular control…

view full answer...

Answer 6

With the entire setup of the B&W Companion #BWRVK3370, the weight of that hitch is 262 pounds. If you are looking for a lighter option, you can go with the Curt E16 5th Wheel Trailer Hitch w/ Slider for Ford Towing Prep Package #C16515-16020.…

view full answer...

Answer 7

The shipping weight of the B&W Companion OEM 5th Wheel Hitch #BWRVK3305 is 152 lbs so it will be just under that after you remove the packaging. Although it is still pretty hefty, the head unit part #BWRVC3006 can easily be removed off of the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Control Panel For An Atwood GC10A-3E RV Water Heater

Product Page this Question was Asked From

Continue Researching