Replacement Parts for Sleeve-Lock Couplers

Question

Question:

Is there a repair kit for a 2” sleeve lock hitch

asked by: Jack S

0

Expert Reply:

We do not have many replacement parts for Sleeve-Lock couplers like the item # CA-5196-B you were looking at. We just have the replacement spring item # CA-5196-SPR and the replacement pin item # CA-5196-PN.

expert reply by: Jerred H

0

Jack S.

7/24/2024

Thanks.

Jerred H.

7/24/2024

@JackS You're welcome!

Answer 1

We don't offer any axles or hubs that are compatible with that wheel bearing set, but a 1-3/4 inch square axle would typically carry a 1000-2000 lb capacity. If you were needing a replacement axle, I'd be happy to look through our offerings…

view full answer...

Answer 2

I took a caliper out to our warehouse and measured the Replacement Spring for Ram Sleeve Lock Couplers part #CA-5196-SPR for you, the length is 1.68" and the diameter of the coil is .040".

view full answer...

Answer 3

While I have no way to lookup the parts for your Kodiak Hitch on your Big Tex trailer I believe you are looking for a spring like the Bulldog Replacement #BD500354. This spring has an overall length of 1-7/8". If the spring you are looking for…

view full answer...

Answer 4

Thanks for the photo; it looks like you have a low-profile latch and so the Replacement Coupler Cap Spring #BD500354 would work for your coupler.

view full answer...

Answer 5

It sounds like you might be needing the Replacement Coupler Cap Spring #BD500354 which fits the Bulldog Collar-Lok Couplers. If more than the spring is broken then we'll need to get you a completely new coupler. In this case let me know the what…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Replacement Parts for Sleeve-Lock Couplers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching