Can Curt Ball Mount Be Flipped Over To Achieve A Raise In Height
Updated 02/03/2026 | Published 07/19/2024
Question:
Hello, I have the Curt 2” hitch with 2” ball. Is it safe to flip the mount and remove and reinstall the ball to achieve a raise? Will the tow capacities of the mount be the same either way? Thanks!
asked by: Mike
Expert Reply:
Hi Mike; yes, a Curt ball mount like the # C45056 can be flipped over. This is considered the rise position and will not impact the capacity in any way. I attached a picture below which shows the ball mount in both orientations, both are acceptable. Your ball mount will actually have a rise measurement as shown below which can be used to help determine if it will keep your trailer level.
(click to enlarge)
Product Page this Question was Asked From
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- One Ball
- 2 Inch Ball
- Steel Shank
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Pre-Torqued
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Ford Transit Connect
- Video: 2019 Ford Transit Connect Curt Trailer Hitch Receiver: Complete Installation
- Video: Feature Review Replacement 2" Shank Adapter for Yakima RidgeBack or FullTilt Bike Racks
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Replacement 2" Shank Adapter for Yakima RidgeBack or FullTilt Bike Racks
- Shop: Ladder Rack
- Q&A: Replacing Running Light Wire on Shorelandr Boat Trailer
- Search Results: 2 wire pigtail
- Search Results: 2 wire plug
- Search Results: primary wire
- Search Results: a35w42b
- Search Results: 4 way harness
- Search Results: ring terminal
- Search Results: 11755
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
- Video: Clean Up Your Trailer Wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
on Trailer Hitch Ball Mount
Robin H.
2/3/2026
Hey Mike, how did flipping your Curt ball mount to the rise position work out for your setup? Did it help keep your trailer level as expected? Your update could make it easier for the next person with the same question.