Will Timbrens TTORTUN4 Fit 2016 Toyota Tundra

Question

Question:

I had TORTUN4 bump stops on my 2011 Tacoma. When I sold it I removed the stops. I now have a 2016 Tundra Crew 4wd. Will these work on the Tundra.

asked by: Ralph K

0

Expert Reply:

Hey Ralph,

Yep, the Timbren Rear Suspension Enhancement System # TTORTUN4 will indeed fit your 2016 Toyota Tundra.

expert reply by: Kyle S

0

Robin H.

2/3/2026

Hey Ralph, how did the Timbren bump stops work out on your Tundra? Your experience could point others in the right direction.

Answer 1

Hi Duane! As long as your 4 wheel drive 2023 Toyota Tacoma has 4 leaf springs in the rear, the Timbren Rear Suspension Enhancement System #TTORTUN4 will indeed fit. If you do not have 4 leaf springs, just let me know and I can find another option for…

view full answer...

Answer 2

Hey Fernando, I'd be happy to help you pick out the correct Timbren rear suspension kit for your 2023 Toyota Tacoma TRD that will be towing a trailer. Really it comes down to two options. You would want the part #TTORTUN4L for if you have the 3…

view full answer...

Answer 3

Hello again Chris; the #T68MR is for the severe service kits that fit the 2000-2021 Tundra. These are designed for heavy applications under constant load like a salt spreader. Since you will be using the standard Timbren SES #T45MR the Spacer Kit for…

view full answer...

Answer 4

The Timbren Active Off-Road Bumpstops - Rear Suspension - 3,600 lbs #TABSTRFK have bump stops and mounts that are 5-1/2 inches tall overall and u-bolts that are 8-1/4 inches long and 3-3/4 inches on center. I've attached a photo to assist. These…

view full answer...

Answer 5

Suspension enhancement systems like Timbren springs are perfect for the scenaro you're describing. These solutions supplement your factory suspension but don't necessarily increase your capacity. Timbrens are hollow rubber springs that sit…

view full answer...

Answer 6

The Timbren Active Off-Road Bumpstops part #TABSOSR which are a fit for a 2007 Toyota Tacoma are designed so that there is more space between the spring and frame to allow the suspension to articulate freely when off-road. If you're looking for a…

view full answer...

Answer 7

As long as you stay under the 10,300 pound mark you should be fine. Currently your trailer and gear estimate would weigh 9,100 pounds. Take a look at the rig when the trailer and truck are fully loaded as though you were ready to hit the road. If the…

view full answer...

Answer 8

Hi Dustin; according to Timbren the #TABSOSR cannot be used with spacers. To get the support you want without switching kits I would try reaching out to Timbren again since they do have a satisfaction guarantee. When they have been here in the past…

view full answer...

Answer 9

Hello Jhon, thanks for reaching out. Both the Timbren kits you mentioned are going to fit the 2013 Toyota Tacoma. The difference is the application and the weight capacity. The #TABSOSR are intended for off-road applications and are rated for 3,600…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Will Timbrens TTORTUN4 Fit 2016 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching