Voyager WiSight 2.0 Adjustment Instructions

Question

Question:

need instructions for using and adjusting my camera settings Voyager Voyager WiSight 2.0 RV

asked by: Joe M

0

Expert Reply:

Hey Joe, I found a PDF of the instructions online for your Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RVs # ASA37YR and attached a cutout of the adjustment instructions.

If you have any other questions let me know in the comments and I'll see what I can do to help you out.

expert reply by: Bryce D

0

Camera Adjustment Instructions
(click to enlarge)

Answer 1

Hey Roy. I could not find anything when I searched Voyager model WVOMAP. Do you see any other numbers or model labels? You can add this information and any other questions you have where it says Reply to Jerred H and I'll be happy to answer them.…

view full answer...

Answer 2

There isn't an adapter to connect the wiring of a Furrion camera to a Voyager. With that said you can pretty easily just cut the connectors off and then connect to the camera since it's only two wires.

view full answer...

Answer 3

A wireless camera like the Voyager WiSight 2.0 Wireless RV Backup Camera System #ASA84YR gets its power from the running light circuit on a trailer. So this would require the running lights or headlights on your vehicle to be on when connected to the…

view full answer...

Answer 4

The easiest way to install the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision #ASA84YR on your Airstream Basecamp trailer is to wire it to the running lights circuit, which will allow the camera to be on all the time as long as…

view full answer...

Answer 5

The Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RV - 4.3" Screen #ASA24YR you were looking at is both the camera and the monitor and is the second generation of Voyager's camera systems. If you are trying…

view full answer...

Answer 6

I have attached for you below the pairing procedure for the Voyager WiSight Wireless RV Backup Camera System part #ASA84YR. Please note, a mistake I have made in the past was applying power to the camera too soon, this cannot be done until the…

view full answer...

Answer 7

That is exactly what the adapter was designed to do. The Furrion #FR87PR is designed to provide the proper amount of voltage on the running lamp circuit of the 7-way so a camera system will receive enough power to operate reliably. Ford and GM 2019…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Voyager WiSight 2.0 Adjustment Instructions

Product Page this Question was Asked From

Continue Researching