7-Way Wire Harness Needed For A 2024 Ram 5500

Question

Question:

Hello I have a Ram 5500 going to build a bed for it , what wiring harness works with this that has a double out put one for trailer and one for gooseneck? thanks

asked by: Gabriel A

0

Expert Reply:

Hey Gabriel,

You would need a factory wire harness from Dodge first and could then install the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole # PK11893-33-32 inline with the factory harness to get a 7-way socket in the bed of the truck as well.

expert reply by: Kevin C

0

Answer 1

The B&W Companion 5th Wheel Trailer Hitch #BWRVK3500 (RVK3500) is the complete 5th wheel hitch that will mount to an existing B&W Turnoverball Gooseneck Hitch socket in the truck bed. The part #BWRVB3500 (RVB3500) that you also referenced is…

view full answer...

Answer 2

Hey Chris, Our Fitguide can be a bit confusing sometimes. Essentially the whole category is broken down into whether they fit diesel or non-diesel models. Since the EcoHitch Hidden Front Mount Trailer Hitch Receiver #EH37FR fits both gas and diesel…

view full answer...

Answer 3

Yes, the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1111-30 will fit your 2024 Ram 3500 long bed dually. This hitch fits both the short bed and long bed including dually and single rear wheels. It will replace your factory hitch.

view full answer...

Answer 4

Hello Jason, I have a solution for you, but I don’t know of any hitch plates that allow you to change out the ball. You’ll want to go with the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks #BWGNRK1500. When you look at the…

view full answer...

Answer 5

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 6

Hey Ross. The Buyers Products 42" x 13-1/2" Gooseneck Hitch Plate with 2-5/16" Ball And Two D-Rings item #3373014981 is designed to be bolted or welded directly to your truck's frame. You won't need any crossmembers but…

view full answer...

Answer 7

Unfortunately I cannot pin point where the brake light switch is on a 2007 International 4400 series. You'll need to trace your air line to find the wiring connection and then confirm the correct wire using a circuit tester like #PTW2993. This…

view full answer...

Answer 8

Since there isn't an adapter to go from a semi 7-Way to an RV 7-Way the best solution is going to be to install a separate RV style 7-Way on your 2007 International 4400. You can use installation kit #ETBC7. You may be able to tap into the…

view full answer...

Answer 9

Hey Matthew. No one makes a custom fit gooseneck hitch for a Silverado 5500 but we do have a couple of options depending on how your truck is setup. If you have a flatbed truck or one with a regular bed, you can use the B&W Turnoverball Underbed…

view full answer...

Answer 10

Hey Roger. In order to get you the correct Reese goosebox, I'll need the information on the sticker that's attached to your current pin box. The sticker should say date of manufacture, possibly weight capacity, and have some form of RPO, LCI,…

view full answer...

Answer 11

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 12

Yes, we also have the Replacement Right Arm #Y76KV for the Yakima EXO SwingBase #Y34VR. This is the other side from the Left Arm #Y66KV you found.

view full answer...

7-Way Wire Harness Needed For A 2024 Ram 5500

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching