Replacement Air Bags and Fitting for Air Lift 5813

Question

Question:

We are looking for 2 replacement air lift bags 5813 for ones that are getting worn out. Just need the top fittings and the bags, thanks, al

asked by: Alan H

0

Expert Reply:

If you're referring to the 90 degree fitting on top it is the # AL21848. We no longer carry the replacement air bag, which is the Air Lift 50201. I searched for this part and it looks like Air Lift still carries it so you can get it directly from them.

expert reply by: Robin H

0

Answer 1

The correct replacement airbag for your Air Lift LoadLifter 5000 part 5813 is the Replacement Air Spring for Air Lift LoadLifter 5000 part #AL50201.

view full answer...

Answer 2

First you will want to completely deflate the airbags. Then to remove the air line from a push to connect fitting like part #F3128-1 you first push the outer metal ring inward and then pull the air line out. You may also need to push in on the air…

view full answer...

Answer 3

We do have those replacement parts for the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88338 on your 2017 Chevy Silverado 2500. The clamp bars and fittings are sold indivuidually so you will need 2 of each from the lift below: Replacement…

view full answer...

Answer 4

The replacement elbow fitting you need for the Air Lift Air Bag Kit part #AL59561 that you referenced is the part #AL21848.

view full answer...

Answer 5

To remove the valve on the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL88338 you will need to remove the air spring from your truck. You can't turn that valve inside the bracket. Once off I recommend using the Replacement…

view full answer...

Answer 6

There isn't a special tool for removing the #AL21848 from the air bags. You'd need to use a wrench. If you can't make a complete revolution you'd need to take smaller turns based on the limited access. You may need to remove the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Air Bags and Fitting for Air Lift 5813

Product Page this Question was Asked From

Continue Researching