Trailer Hitch Receiver Compatible With a 2014 Isuzu NPR

Question

Question:

I am looking for a compatible trailer hitch for a 2014 Izuzu NPR. What do you suggest?

asked by: T.j. M

0

Expert Reply:

The Draw-Tite Universal with the 7" Tall Brackets # 41990-07 or 16" Tall Brackets # 41990-16 are some of the better options for your 2014 Isuzu NPR. The height brackets you will need will depend on what kind of up-fit your vehicle had done to it. The brackets themselves can be either bolted or welded to the frame on your truck which allows you to position it where it will fit best and work with any lifts or bumpers you already have.

expert reply by: Bud M

0

Answer 1

I will be happy to provide you with the dimensions and hole spacing on the brackets included with trailer hitch #41990-07 to see if it will work on your cab and chassis 2004 Ford F-550. I have included a picture with the measurements.

view full answer...

Answer 2

In order to add a hitch to your 2011 Ford E-450 Shuttle Bus you need the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07. There are no custom fit hitches for your E-450, so a universal weld-on hitch is the only option. This is a…

view full answer...

Answer 3

According to my technical contact at Draw-Tite your 1989 Chevrolet R3500 cab-and-chassis with dump box has no direct-fit bolt on hitches available. However, there may be an option in a universal-fit weld on Class V hitch. Curt offers a universal-fit…

view full answer...

Answer 4

I have a solution for you but the brackets on the Curt item #15903 can not be cut and there are no shorter options. I recommend using the Draw-Tite Trailer Hitch item #41990-07 instead. This is also a class V universal hitch with a 2" receiver.…

view full answer...

Answer 5

For your 2006 Ford F-450 Shuttle Bus you are going to need to use a universal hitch. For this you will need to measure how wide your frame rails are apart on the rear of your bus. Then you will need to know how much drop from the frame rails to the…

view full answer...

Answer 6

We have a hitch option for your 2006 Itasca Suncruiser, but the #C15400 is 32.94" wide overall and the bolt holes are 30.31" apart from each other. So what you will need is a universal weld-on hitch, which will fit so long as the frame on…

view full answer...

Answer 7

No, it won't but I have a hitch that will. I checked with Buyers Products and the frame's a different width on the newer Savana cutaways so the item #3371801102 won't work. Since there are no custom fit hitches for a 2010 GMC Savana…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Trailer Hitch Receiver Compatible With a 2014 Isuzu NPR

Continue Researching