What Is The Recommended Tongue Size For The Dexter DX7.5L A-60 Brake Actuator DX89FR

Question

Question:

What is the recommended tongue size for Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2inch Ball - Zinc - 7.5K Item # DX89FR

asked by: James C

0

Expert Reply:

Hello James. The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout # DX89FR is designed to work with a 3" wide trailer tongue.

expert reply by: Jesse M

0

Jim

4/2/2024

Is that a 3 inch by 4 inch or 3 inch by 5 inch?

Jesse M.

4/3/2024

@Jim The # DX89FR actuator is designed to be top mounted on a 3" wide tongue. So this could work with a 3" x 3", 3" x 4" or a 3" x 5" tongue depending on your application.

James C.

4/3/2024

Thank you!!

Syo

6/2/2026

I'm using a tie-down actuator LP80, but are there any actuators that can be installed on it without any modifications?

Jesse M.

6/2/2026

@Syo We have replacements for the LP80 like the Dexter # DX89FR which doesn't require much modification provided the LP80 is bolted on not welded. You may have to drill an additional hole in the tongue but that would be it. The holes are 3" apart on center.

Syo

6/2/2026

@JesseM Thank you for your help. I found another eTrailer response recommending the Dexter DX89FR as a replacement for the LP80 with only one additional mounting hole required. Based on the photos I sent, would the DX89FR be a better fit than the Demco DM8669113 for my Ranger trailer? Which option would require the least modification?

Jesse M.

6/8/2026

@Syo Yes, the Dexter # DX89FR is definitely what I recommend. Its a solid unit and will require the least amount of modification.

See All (5) Replies to Syo ∨

Answer 1

Hey Kevin, we have tandem axle brake line kits that would work great on your TA96BT 23-27 EZLoader boat trailer. We have the part #DM6098 which has a 15 foot main line and w have the part #DM5951 which instead has a 16 foot main line. I wasn't…

view full answer...

Answer 2

The Demco Hydraulic Brake Actuator w Drop part #DM8104311 will take a male 3/8"-24 fitting like that on the Demco Hydraulic Brake Hose with Fittings part #DM05982. I am not sure what size fittings you have now but all you would need is an…

view full answer...

Answer 3

The Kodiak 12" Hub-and-Rotor Assembly #KHR12D that you referenced requires an inner bearing of #25580 and an outer bearing of #15123. For a set of brake pads you would want the part #K225CP.

view full answer...

Answer 4

The Demco Hydraulic Brake Actuator part #DM8104311 is a fit for trailer tongues 3" wide. If this is what you have then it will work well. If you are however looking for the bolt hole spacing then you can reference the attached photo.

view full answer...

Answer 5

According to EZ Loader, your trailer uses #LM67048 outer and #25580 inner bearings. The correct bearing kit is the #BK3-310. We have 3 options for disk brake kits for your trailer, with the difference being the finish. The 3 options are as follows:…

view full answer...

Answer 6

The bearing #LM67048 and #15123 that you referenced have the same inner diameter which means they fit the same spindle and the disc brake kit #K2HR526DKG would fit in place of what you have now.

view full answer...

Answer 7

I would be happy to help you set up a disc brake system for you 2012 Tandem axle boat trailer. Let's start with an actuator you are going to want the Titan Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball item #T4750800. This is a bolt on…

view full answer...

Answer 8

I recommend replacing your current surge brake coupler using either using the Demco Hydraulic Brake Actuator for Disc #DM8104311 or Drum #DM8102511 brakes. I prefer these couplers as they have a Zinc finish which best resists corrosion.

view full answer...

Answer 9

Thanks for the photos. It is clear you have a Titan brake actuator like the Brake Actuator with Manual Lockout - Bolt On - Drum - 2" Ball - 7,500 lbs #T63FR. It sounds like you need the Replacement Master Cylinder Assembly for Titan/UFP Brake…

view full answer...

Answer 10

At this time we do not carry a compatible inner member for your Reliable ACT 7.5 KS actuator so I recommend replacing it with the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX89FR. This hydraulic actuator activates trailer's brakes…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What Is The Recommended Tongue Size For The Dexter DX7.5L A-60 Brake Actuator DX89FR

Product Page this Question was Asked From

Continue Researching