How To Install E-Track Inside Of A Isuzu Refrigerated Truck
Updated 04/01/2024 | Published 03/30/2024
Products Featured in This Question
Question:
Hello good morning.. I have a 5 ton Isuzu refrigerated truck... Im wondering what is the best way to install 18 ft long e track/channels on each side of the truck.. I want to make sure its sturdy and safe so when I strap pretty big loads to the side of the walls. Nothing ruins the walls of the truck or makes any holes and its sturdy.. PLEASE let me know ASAP.. thanks again much appreciated...
asked by: Shawn
Expert Reply:
Hey Shawn,
The E-track you're wanting to install in the back of your truck is just going to need to be screwed into the studs of the walls or into the floor. You'll want some self tapping screws ( # SL99FR) or wood screws ( # SL49FR) that are just thin enough to pass through the mounting holes of the E-track # e62VR and just long enough to bite into the studs without passing completely through them. The more screws the better the hold so you can load up each hole, even if some holes are just passing through thin sheet metal walls and not hitting a stud. If passing through only thin walls with no studs then you can use backing plates like part # e76YR to help secure the tracks.
Once installed you can use anchor points like the # e87HR to secure your loads.
Product Page this Question was Asked From
CargoSmart Shelf Brackets for E Track or X Track Systems - 12" Deep - 1,000 lbs - Qty 2
- E Track
- E Track Cargo Organizers
- Shelf Brackets
- CargoSmart
more information >
Continue Researching
- Search Results: etrack backing plates
- Video: NATM Vendor Interview: Brophy - Truck Bed Tie Downs Anchors
- Shop: Snap-Loc E-Track Self-Drilling Metal Screws - Qty 20
- Shop: Snap-Loc E-Track Wood Screws - Qty 20
- Shop: CargoSmart X Track Trailer Shelf Bundle - Matte Black - Steel - 667 lbs - 5' Long
- Video: Let’s Check Out the Snap-Loc E-Track Wood Screws
- Video: In-Depth Review of the CargoBuckle G3 Retractable Ratchet Tie-Down Strap
- Video: All About the etrailer Horizontal E Track
- Video: etrailer Horizontal E Track Spec Review
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 4-7/8" Wide - Recessed Mount - 1,600 lbs
- Shop: CargoBuckle G3 Retractable Ratchet Tie-Down Strap - Flush Mount - 2" x 6' - 1,167 lbs
- Shop: etrailer Horizontal E Track - Galvanized Steel - 2,000 lbs - 94" Long - Qty 4
- Shop: Durabilt Hammerlock Coupling Link for 1/2" Chain - 12,000 lbs - Qty 1
- Search Results: e track
- Search Results: vertical e track
- Video: A Closer Look at the Powerbuilt Brake Bleeder
- Video: Complete Breakdown of the CargoSmart Folding Workbench Brackets for E Track or X Track
- Search Results: straps
- Search Results: 7~223
- Search Results: e track strap
- Search Results: rotor
- Q&A: Mounting Flange Bolt Pattern for Trailer Valet Electric Tongue Jack with Digital Tongue Weight Scale
- Article: Trailer Wiring Diagrams
- Q&A: Maximum Tongue Weight for B&W Digital Tongue Weight Scale
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Can I Run Velit 12V Air Conditioner In My Camper Van While Driving?
- Q&A: Replacement for a Tie Down 70lc Brake Actuator
- Q&A: Does Replacement LED Strip Light LC423331 Fit Lippert Awning Rail Channel
- Q&A: Recommended 33-1/4 Inch Cam-Door Lock for Enclosed Trailer
- Q&A: Difference Between Oil and Grease Seals
on E Track
