Is There an Extension For 7-Way Trailer Wiring Harness

Question

Question:

I am looking for a wire harness extension 7pin connector. I can send you pictures. Thanks

asked by: Diego L

0

Expert Reply:

Hey Diego; we do have an extension for your 7-pin trailer wiring harness, the 10' long TorkLift Wiring Harness Extension # TLW6510.

expert reply by: Kyle S

0

Answer 1

The back edge of the front most rail would be 47-1/2 inches forward of the rear edge of the truck bed (not the tailgate) for a short bed truck or 52-3/8 inches on long bed trucks. You can see these measurements in the diagram I grabbed from page 2 of…

view full answer...

Answer 2

The Head Unit and R16 Roller Adapter #C16515 is more of an entry level fifth wheel head designed for a lower price point, whereas the A16 part #C16520 is a bit nicer with it's 2 piece jaw system that will provide better king pin contact which…

view full answer...

Answer 3

The switch on your pin box is probably the breakaway switch. One wire from the switch will go to a 12v battery on the trailer and the other wire will tap into the electric brake wire on the trailer (typically a blue wire). I have attached an…

view full answer...

Answer 4

Yes, the heat shield on your 2017 Chevrolet Silverado 3500 while installing the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1016 will need to be removed and then discarded. The heat shield is not a…

view full answer...

Answer 5

In step 2 of the instructions for the B and W Turnover Gooseneck Hitch part #BWGNRK1012 that you referenced you will end up removing the heat shield. Some of our customers have reported back saying that they did not have to remove it but others said…

view full answer...

Answer 6

Actually, the structure of the B&W #BWGNRK1016 Turnover Ball gooseneck hitch protects the underside of the bed much better than the heat shield could. The hitch is much thicker and heavier than the heat shield was, so there'll be no worries…

view full answer...

Answer 7

If there's ever an issue with the signal on a Furrion camera system is almost always comes down to lack of power. Plugging in your #FOS43TASF to the monitor cable is giving you a direct 12 volts to the camera whereas when installed on the trailer…

view full answer...

Answer 8

There is not a Group 26 battery box for some reason. The smallest battery box available that will fit your 9" L x 6-1/2" W x 8-1/2" H battery is the Tow-Rax Battery Box #TWSP12B. This measures 12" long x 8-7/8" wide x…

view full answer...

Answer 9

Typically, you want between 16" and 24" of wire to extend past the trailer tongue but it really depends on your particular vehicle and the location of the trailer plug on your vehicle. You want enough wire so that there is not tension on…

view full answer...

Answer 10

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

It's very common for smaller single axle trailers to have brakes installed on them already. Most likely if you look you'll find options in the size you want that are already set up with brakes. This would be the easiest and most cost…

view full answer...

Is There an Extension For 7-Way Trailer Wiring Harness

Product Page this Question was Asked From

Continue Researching