What Does MORryde RV Cargo Sliding Tray CTG60-2048W Weigh

Question

Question:

How much does a CTG60-2048W MORryde RV Sliding Cargo Tray weigh?

asked by: Gregory J

0

Expert Reply:

Hey Gregory, the MORryde RV Cargo Sliding Tray CTG60-2048W part # MR94FR weighs 73 lbs.

expert reply by: Jameson C

0

Answer 1

We do have the Replacement Step Latch #MR97BR you can order for the MORryde Step Above RV steps. This latch mounts to the left side of the step as you are facing the door from outside the camper.

view full answer...

Answer 2

The MORryde RV Cargo Sliding Tray - 90" x 36" - 2 Way Slide #MR38FR weighs 150-lbs. This cargo tray has a maximum weight capacity of 800-lbs, measures 90" long x 36" wide x 6-5/8" tall, and the tray measures 88-1/4" long…

view full answer...

Answer 3

Hello Greg. I do have a potential solution for you, but the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter #CAB-C5G that you were looking at will not work for this purpose. Reason being that this kind of adapter is not compatible with a…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 10

With a 2022 F350 short bed, hitting the top of the bed rails should not be an issue with most campers. Turning clearance however, will certainly be a factor. That is one advantage of the Andersen Ultimate hitch #AM3200, as it provides a 9"…

view full answer...

Answer 11

Hey Bob, thanks for reaching out, and good question. For that setup, as long as the tray is properly secured in the portion that is touching the floor, it will be just fine. It might be a bit more difficult to install since you can't secure the…

view full answer...

Answer 12

Hi Chuck! The MORryde RV Cargo Slide Tray - 72" x 26" - 1 Way Slide - 60 Percent Extension - 800 lbs #MR67FR sits 1.6 inches above the floor you mount it on. If you want or need it to be a bit higher off the floor, you can also grab the…

view full answer...

What Does MORryde RV Cargo Sliding Tray CTG60-2048W Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching