Replacement Hub/Drum and Brakes for a TetonX Trailer
Updated 02/29/2024 | Published 02/28/2024
Products Featured in This Question
Question:
I have a TetonX with Timbren 5200 axles and am looking for the inner seals item #/link Im also looking to chanage the backing plate to one that supports a parking brake - is item # 23-112-113 the correct part? I also want to remove the spacer blocks which are only used to match the lug pattern and get a toyota 6 on 5-1/2 pattern. Is item # 8-201-9UC3-EZ correct? Should I replace the spindles while Im in there? I might want to carry a spare in any case.
asked by: Wendell R
Expert Reply:
Yes, the 12" Dexter Electric Trailer Brakes - Parking Brake Ready # 23-112-113 and the Dexter Trailer Hub and Drum Assembly 6 on 5-1/2 # 8-201-9UC3-EZ are an excellent combination for your TetonX trailer.
Unless your spindles are in bad shape I'd leave them alone. Usually when spindles look like they need to be replaced it's because some major damage has happened and a lot of times the whole axle being replaced isn't uncommon. Should you decide to have a spindle (or a few of them) on hand then you'll want the #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter # TRU37FR for that application.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 6 on 5-1/2 - Pre Greased
- Trailer Hubs and Drums
- Hub with Drum
- Pre-Greased
- 25580 / 15123
- Standard Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Dometic Soft Start for Dometic B59516.711C0-MX
- Q&A: How to Add Timbren Axleless Suspenion to a Trailer and Use 5 x 5 Lug Jeep Wheels
- Q&A: Victron Smart Dongle vs Cerbo GX Explained for MultiPlus-II Remote Control
- Q&A: Can A Hub With A 15123 Bearing Be used To Replace A Hub That Used An LM67048 Bearing?
- Q&A: Will TruRyde Trailer Hub and Drum Assembly Fit 2019 Travel Trailer With 3,500 lb Axle
- Q&A: Replacement Brake Assemblies and Hub/Drum for Airstream with Nev-R-Lube Hub/Drums
- Q&A: Wiring Diagram for Installing the Replacement Single Zone Thermostat for Dometic RV Air Conditioners
- Article: Trailer Brakes Not Working? Troubleshooting Guide
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Trailer Wiring Diagrams
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
Wendell R.
2/28/2024
Do you know the item # for the inner seal for the existing hub? I had to replace the existing bearings and the seal on one side and was able to get spare bearings, but the parts store only had the one seal. I'd like to get a spare seal now, before I replace everything.