Can Extang Tonneau Cover Replacement Corners # EX4211 fit a Lund Genesis?

Question

Question:

Will extang 4211 corner end piece for tonneau cover fit Lund Genesis? Lund part no. is LND 1403235? Thank you

asked by: Tolbert F

0

Expert Reply:

Based on the images I could find for the Lund part 1403235 I do see they are different than our Replacement Corners # EX4211 from Extang. As we do not carry Lund covers I cannot verify if these could be modified to still fit inside your Lund Genesis cover.

expert reply by: Bud M

0

Answer 1

Hello Sherwin, I am happy to get the correct part for you. Can you please respond directly to the email that you receive with a picture of the plastic clip you are referring to? I am also going to need the date code or serial number off of the the…

view full answer...

Answer 2

We have some replacement parts for Extang Trifecta Tonneau Covers. We have a cab side hinge #EX1032 and a Tailgate side hinge #EX1033. We also have some clamp accessories I've linked to assist. We also have the corner brace assembly #EX1041 and…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Can Extang Tonneau Cover Replacement Corners # EX4211 fit a Lund Genesis?

Continue Researching