Video that Shows Trailer Valet MV Pro in Use

Question

Question:

about part # TV96FR Have you guys tried this out on a reasonably big trailer? The concept is intriguing to me, but I am a little skeptical about how well it might work and how usable it is. I would like to see a video of it in action. I have a 8.5x24foot box trailer that I would like to move around the yard. Empty it weighs 5400 lbs with a 10k GVWR. Well within the specs of this, but I am still skeptical.

asked by: SHERMAN G

0

Expert Reply:

Hey Sherman, so the Trailer Valet MV Pro part # TV96FR is a newer version of the Trailer Valet XL which we did have the chance to use on larger trailers like what you mentioned. If you check out the review video we shot for that version of the dolly you can see how well it worked for us. Both versions of this dolly are very similar so the video would be a great representation.

expert reply by: Jameson C

0

Answer 1

Hey Michael, so the Trailer Valet Jack part #TV96FR that you referenced actually comes with the drill attachment so you do not need to have the correct size on hand. If for some reason you need a replacement you would want the part #TVDA. It is not a…

view full answer...

Answer 2

So you can use the Trailer Valet RVR9 Remote-Controlled Trailer Dolly #TVRVR9 you were looking at, at a maximum of 5 degrees of incline, but since your trailer is about a thousand pounds heavier than what the dolly can handle you won't be able to…

view full answer...

Answer 3

Hey Ned, the Trailer Valet RVR12 Remote-Controlled Trailer Dolly item #TV59FR has a 5 degree slope limit on a paved concrete surface. The best option I have is going to be the Trailer Valet XL Trailer Dolly with Chain Drive item #TV96FR. The Valet XL…

view full answer...

Answer 4

The Trailer Valet MV PRO Trailer Dolly #TV96FR is their all new dolly and is listed under their Products/Trailer Movers. This is going to be overkill for your Lance 1685 since the dolly is rated for trailers up to 12,000lbs and your Lance is going to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...