Locking Hitch Pin For The Curt QuickPin No-Latch Trailer Coupler for 2" Ball # C82CR

Question

Question:

Thank you, that helps. The video for the Curt No-Latch says that there is an option for a locking pin for the 2” and 2-1/2” wide coupler. Is that correct? Thanks again. Ed

asked by: Ed D

0

Expert Reply:

Hi Ed,

Yes, the pin # C87ER included with the Curt QuickPin No-Latch Trailer Coupler for 2" Ball # C82CR is 1/2" diameter so you could use a locking hitch pin lock like the Curt # C23517. This locking hitch pin is 1/2" in diameter with a 2-13/16" span to fit the width of the coupler.

expert reply by: Kevin C

0

Answer 1

Best option we have is the part #e98887 for a pin lock for the Demco coupler part #DM15000-52. This has a pin diameter of 1/4 inch and a length of 2-1/2 inches so it will fit tight to your coupler and fit well still.

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 4

The HydraStar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi #HBA16 you were looking at is the correct Electric Over Hydraulic actuator for the disc brakes on your tandem axle boat trailer. You can lock out your Titan Model 10 surge…

view full answer...

Answer 5

The lock I recommend for the Demco Channel Tongue Trailer Coupler - eZ-Latch #DM15000-52 is the etrailer Trailer Coupler Lock #e98887. This lock is going to do a great job of keeping your trailer safe and sound and will work perfectly with the Demco…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Locking Hitch Pin For The Curt QuickPin No-Latch Trailer Coupler for 2" Ball # C82CR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching