Can the Replacement Leg Kit for RV Dinette Tables Be Shortened
Updated 09/25/2024 | Published 01/27/2024
Products Featured in This Question
Question:
Can you cut the pipe to make the table set lower?
asked by: David L
Expert Reply:
Yes absolutely, you can cut the pipe to whatever length you want. You're just going to want to make sure that the end caps get put back together properly so you can install the leg to the mount.
If you only need to trim it a little bit you could just use the Replacement Leg Kit for etrailer RV Dinette Tables # e69RR which is going to be 2 inches shorter than # e79RR.
Patricky
9/24/2024
Bryce, I’ve tried several techniques for removing the endcap of the one I already own. So far, it won’t budge and I’m afraid I will damage it. To be confident that your version will come apart more easily, can you assure me that I won’t struggle? Not sure how this one was assembled. Perhaps with heat or some special glue? I’d appreciate any advice from you. I don’t even care if I have to buy two new legs and cut them myself. I just don’t yet know how to get the end off. Thanks! Patrick
Product Page this Question was Asked From
Replacement Leg Kit for etrailer RV Dinette Tables - Surface Mount
- RV Dinette Table
- Legs Only
- Surface Mount
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: rv table mount
- Search Results: foot stool
- Q&A: Are the Mounting Brackets for the Replacement Leg Kit for etrailer RV Dinette Tables Made of Metal?
- Video: Detailed Breakdown of the Replacement Leg Kit for etrailer RV Dinette Tables
- Shop: Replacement Leg Kit for etrailer RV Dinette Tables - Recessed Mount
- Shop: Replacement Leg Kit for etrailer RV Dinette Tables - Surface Mount
- Q&A: How Many Legs Should I Use With My 27" x 37" RV Table?
- Video: Review of Empire Faucets RV Showers and Tubs - Quick Disconnect Faucet and Flex Spout - EM74JR
- Video: GSI Outdoors Pinnacle Pro Camping Stove Feature Review
- Search Results: license plate bracket
- Search Results: legs only rv dinette table
- Search Results: hose fittings
- Search Results: camp stoves camping kitchen
- Shop: Empire Faucets Quick Connect Shower Valve and Flexible Spout for Exterior RV Showers - White
- Shop: Valterra Check Valve for RV Fresh Water Systems - 1/2" MPT x 1/2" FPT - Brass
- Shop: GSI Outdoors Pinnacle Pro Camping Stove - 2 Burner - 11,000 Btu/h
- Shop: Hose Extender for Empire Faucets Quick Connect Outdoor RV Faucets - 15'
- Shop: Suspension Enhancement
- Shop: RV Mattress
- Video: In-Depth Review of the Roadmaster Reflex Steering Stabilizer with Mounting Brackets
- Search Results: anti~sway bars
- Shop: Pacbrake Alpha HD Pro Air Bag Suspension Kit w/ Internal Jounce Bumpers - Rear Axle - 5,000 lbs
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Firestone Air Bags for 2026 Ford F-350 FX4 Dually
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
on RV Dinette Table
Patrick Y.
9/22/2024
I want to buy a second leg to support a custom driver’s table (double pedestal). The two floor mounts will be mounted at different levels with one on the floor and one on the doghouse. If I purchase your 26” support and want to shorten it, how might I remove the end cap without damaging it? There is no obvious way for me to remove the endcap of the one I already own. Thanks!