Replacement Lid for Dometic Roof Vent Lid FA1250

Question

Question:

Im wondering if this part fits my Dometic fan, model number FA1250?

asked by: Dennis C

0

Expert Reply:

Since the Dometic FA1250 has a round lid and not a flat lid the correct replacement is the part # FVK1020-19 which it looks like you already ordered so you are good.

expert reply by: Jameson C

0

Answer 1

Since your vent cover goes up higher than the MaxxAir II RV and Enclosed Trailer Roof Vent Cover #MA86JR and you mention the motor on your fan, you most likely need to replace the cover with the MaxxAir FanMate Rain Cover - Smoke #MA00-955003 so you…

view full answer...

Answer 2

RV roof vent covers throughout the industry max out at 10-1/4" tall so you'd be limited to this height. Manufacturers know that this won't allow for the vent lid to fully open but have stated that as long as the lid is opened at least…

view full answer...

Answer 3

The MaxxAir FanMate Rain Cover in Black #MA00-955002, smoke #MA00-955003, or white #MA00-955001 are confirmed to fit the rounded factory mounting points like you see on the attached photo. If you have the flat mounting anchor points like in the other…

view full answer...

Answer 4

MaxxAir and Fan-Tastic Vent Fans are two different brands so you'd be better off with a cover like the Dometic FanTastic Ultra Breeze Trailer Roof Vent Cover #FVU1500BL or #FVU1500WH (white). The MaxxAir II RV and Trailer Roof Vent Cover w/…

view full answer...

Answer 5

These are universal fits so yes, your Fan-Tastic vent is compatible with the MaxxAir II RV and Trailer Roof Vent Cover with EZClip #MA86JR. Since yours is an older Fan-Tastic model, you will need to drill screw holes in order to use this vent cover…

view full answer...

Answer 6

Since your RV has Maxxair roof vents already the vent cover you'd want is the part #MA86JR which was designed for this application. It won't allow the lid to fully open but once it reaches the top of the vent it won't continue to try and…

view full answer...

Answer 7

I confirmed with Dometic in the past that they only carry two styles of lids for the Fan-Tastic Vent line; flat or dome. From there you can then just choose your preferred color. If you have a Fan-Tastic Vent RV roof vent then you'll just need to…

view full answer...

Answer 8

Thank you for the photos! From what I'm seeing it looks like you need the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents #BV0554-01 which has a continuous hinge and then the Replacement Dome for Fan-Tastic Vent RV Roof Vents…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Lid for Dometic Roof Vent Lid FA1250

Products Featured in This Question

Continue Researching