Replacement Snapper Pin for Buyers Products 50 Ton Air Compensated Pintle Hook

Question

Question:

Is it possible to buy a part within that pintle hook assembly? The piece you lift to open the jaw, and thats also secured by the lynchpin. Its got a T top. Its the piece that prevents the jaw from opening while in the closed position.

asked by: Conner

0

Expert Reply:

We have the replacement snapper pin for the # 337PH50 with the part # 3373006875. We do not have the replacement lever though.

expert reply by: Jameson C

0

Answer 1

The Buyers Products 50 Ton Air Compensated Pintle Hook #337PH50 has a bolt pattern that is 5" on center from the left to right holes. The Top to middle holes are 2-3/8" on center and the middle to bottom holes are 2-1/8" on center. The…

view full answer...

Answer 2

The Buyers Products 50 Ton Air Compensated Pintle Hook #337PH50 that you referenced features 3/4 inch diameter bolt holes.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

It sure will Hans and congrats on the new Outback! The Redarc Tow-Pro Link Bluetooth Brake Controller item #RED57AR is going to work great with your 2026 Subaru Outback Wilderness. Since you have the factory tow package, all you'll need to do is…

view full answer...

Answer 12

Hey Andrew. The Redarc Tow-Pro link will indeed work just fine for your 2026 Toyota BZ, and due to it not needing a brake output wire you do not need to hook up the brake out put wire at all. You'll plug the USCAR pig tail #20147 into the Tow-Pro…

view full answer...

Replacement Snapper Pin for Buyers Products 50 Ton Air Compensated Pintle Hook

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching