Wattage Per Bulb in Optronics Two-Bulb Trailer Clearance and Side Marker Light, # MC66RB

Question

Question:

What is the wattage of one of the lamps in the mc66ab

asked by: Jeremy

0

Expert Reply:

The bulbs used in Optronics Two-Bulb Trailer Clearance and Side Marker Light, # MC66RB, are 194 bulbs. The 194 bulb has a wattage of approximately 3.78 watts per bulb.

If you need replacement 194 bulbs you can use # A194B.

expert reply by: Michael H

0

Answer 1

LED lights draw considerably less amperage than incandescent lights. They also run much cooler. These 2 features are why LED lights last so long. The incandescent version of #STL8RB is #ST8RB and it draws 2.5 amps for the stop/turn signal functions…

view full answer...

Answer 2

It sounds as if there is a weak ground connection somewhere on the trailer. Ground issues normally show up when there is more load on a system. Your situation is a perfect example of that. With the running lights on already drawing power, stepping on…

view full answer...

Answer 3

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Wattage Per Bulb in Optronics Two-Bulb Trailer Clearance and Side Marker Light, # MC66RB

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching