Replacement Tailgate Seal and Bed Rail Seal for Pace Edwards Jack Rabbit

Question

Question:

Is this the correct seal for the Jacketrabbit model # TR2028? Do you have the seals for where the cover contacts the tailgate and where the cover slides out of the roll up box? Thank you.

asked by: Rob A

0

Expert Reply:

Yes, the Pace Edwards replacement seal part # PE78UV is the correct replacement for your JackRabbit tonneau cover. Then for the tailgate seal you would want the part # PE99CV. We do not have the seal for the cannister at this time.

expert reply by: Jameson C

0

Answer 1

Right now, the only available tailgate seal that Pace Edwards offers is the rubber seal like the Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV. This tailgate seal will fit the Pace Edwards Bedlocker, Full-Metal,…

view full answer...

Answer 2

We do have the Replacement Tailgate Top Seal #PE99CV, Replacement Sweep Seal Roll #PE78UV and Replacement Bulb Style Tailgate Seal #PE92TJ available like you mentioned. Currently, the "wear" strips are only available in the Replacement Rail…

view full answer...

Answer 3

The part #PE99CV is a totally different seal design from the part #PE92TJ which is a bulb style. They both are tailgate seals for the Pace Edwards Bedlocker but the part #PE99CV is a sweep style seal and the part #PW92TJ is a bulb style. If what you…

view full answer...

Answer 4

The Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV does not come with great instructions. In order to install the Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV, you will need to…

view full answer...

Answer 5

Hello Mark. I had my contact at Pace Edwards run the serial number of your cover. The correct replacement seal will be as follows: Replacement Tailgate Seal for Pace Edwards UltraGroove Retractable Tonneau Cover #PE84AJ

view full answer...

Answer 6

Hey John, thanks for reaching out! The Retrax Replacement Canister Drain Tubes #RE64FR have the same diameter as the Pace Edwards Replacement Canister Drain Tubes #PE55TJ so they are interchangeable, but when I went and checked them out, the Pace…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Tailgate Seal and Bed Rail Seal for Pace Edwards Jack Rabbit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching