Brake Light Switch Wire Color for Brake Controller on a 2012 Jeep Wrangler

Question

Question:

2012 jeep wrangler what color is the brake light switch wire

asked by: Trevor H

0

Expert Reply:

The brake light switch wire on your 2012 Jeep Wrangler should be a white/brown color. This is what you'll connect something like the Prodigy P2 # 90885 brake controller to.

expert reply by: Jon G

0

Answer 1

Hey Howard, for the breakway switch and wiring for your Roadmaster Even Brake #RM-9400 you will need the following parts: -Replacement Breakaway Switch for Roadmaster Supplemental Braking Systems - Qty 1 #RM-650898 -Roadmaster Breakaway Harness for…

view full answer...

Answer 2

Thank you for your multiple recent purchases from etrailer. We appreciate your confidence in us and your repeat business. Thank you also for your included photo. There is a straightforward question/answer process to let you determine if a brake light…

view full answer...

Answer 3

A brake light relay is not required for a 2012 Jeep Wrangler Unlimited. I did check with Roadmaster and they do recommend using a 12 volt power outlet kit, #RM-9332, for any brake system that requires 12 volt power. But a relay is not required on…

view full answer...

Answer 4

It sounds to me like you might have an issue with the connection of the ICX transmitter and the brake signal from the towed vehicle. You're getting the power to the ICX transmitter to activate the Even Brake #RM-9400 but not the signal from the…

view full answer...

Answer 5

I spoke with my contact over at Roadmaster and have some things that you can check. When the Even Brake #RM-9400 pushes on the brake pedal 3 times what it is doing is making sure that it is receiving a brake signal from the cold side of the brake…

view full answer...

Answer 6

I spoke with my contact at Roadmaster regarding the Even Brake Supplemental Braking System #RM-9400. He stated that the Transmitter #RM-9420 is indeed required for proper operation of the system. The transmitter not only sends signals to the monitor…

view full answer...

Answer 7

The Roadmaster Even Brake Portable Supplemental Braking System - Proportional Item #RM-9400 has an inertia sensor that senses deceleration to engage the braking on the towed vehicle. The towed car's brakes are activated at the same time and with…

view full answer...

Answer 8

The monitor for the Brake Pro 9300 is a much simpler design as it's basically just a red LED that lights up that you can see in your rear view mirror which we offer as a replacement part #RM9333-1. The Even Brake uses a transmitter and receiver…

view full answer...

Answer 9

Thank you for your purchase from etrailer of the Roadmaster Even Brake Portable Supplemental Braking System #RM-9400 for your 2019 Jeep Wrangler. As you said, the system does require the use of both the 12 Volt Outlet Kit #RM-9332 and the Roadmaster…

view full answer...

Answer 10

When installing the Replacement Breakaway Switch #RM-650898 for your EvenBrake 9300 supplemental braking system you will need to use the Replacement Wiring Harness for Breakaway Switch #RM-650899. These will be the two parts you are going to need to…

view full answer...

Answer 11

I will be happy to explain the installation of the breakaway switch. First, mount the break away switch at the front of the vehicle, on the drivers side. Choose an area you can easily reach, with a surface of sufficient strength to hold the switch…

view full answer...

Answer 12

According to the installation instructions for the Roadmaster Even Brake Portable Proportional Braking System #RM-9400 (please see step D on page 7) the #1 terminal on the ICX transmitter should be connected to the green wire with spade connector if…

view full answer...

Brake Light Switch Wire Color for Brake Controller on a 2012 Jeep Wrangler

Featured Help Information

Miscellaneous Media

Continue Researching