Offfset Latch for DEF and Fuel Tanks

Question

Question:

I am looking to replace my 2 diesel and 1 DEF doors with keyed-alike cam locks 3 total. They are larger than most I have seen out there. I have enclosed a picture of an existing lock with sizes I measured with caliper. Do you have something that would meet my needs? Thanks!

asked by: Paul F

0

Expert Reply:

Thanks for the picture with the dimensions you need from your offset lock core. We have the JR Products lock core part # 372315 that matches what you would need. You'd need to use the offset latch that comes with it instead of the straight latch.

expert reply by: Jameson C

0

Cam Latch Dimensions
(click to enlarge)

Answer 1

The Replacement Cam Lock Cylinder for RVs #295-000077 is the lock core only. If you are needing the entire lock assembly we have the following options available depending on the size of your lock. Compartment Door Key Lock - 5/8" #372305…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

Hey Steve, The AirLift airbags with internal jounce bumpers are not able to be added to a system without so you would need to get a whole new system. With that said the system with the internal jounce bumpers is going to create a much rougher ride…

view full answer...

Answer 9

Hi Duane, Air Springs are better for leveling loads and will typically give you a rougher unloaded ride quality so these might not be the best option for your setup depending on what your intended use is. Air springs are the best option when it comes…

view full answer...

Answer 10

Hey Jeff, I would strongly recommend the SumoSpring kit part #SS96EV for your 2025 Nissan Frontier. This will give you the support you are looking for without causing the ride quality to be overly harsh which the Timbrens are known to do. Install is…

view full answer...

Answer 11

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Offfset Latch for DEF and Fuel Tanks

Product Page this Question was Asked From

Continue Researching