What Is the Ball Size of the Suction Cup Mounting Bracket for Voyager Wireless Observation System

Question

Question:

Are you able to tell me the size of this mounting ball? 20mm? 17mm? It is part of the suction cup mounting system, item #PVOS5SCM.

asked by: David W

0

Expert Reply:

The ball size for the Replacement Suction Cup Mounting Bracket for Voyager Digital Wireless Observation System # PVOS5SCM is going to be 21mm.

expert reply by: Bryce D

0

Answer 1

Hey Pat, We do have the correct replacement suction cup mount for your WiSight 2.0 monitor WVSXM70, though it's different than the one you asked about. Instad, the correct mount is the Replacement Suction Cup Mount Kit for Voyager WiSight 2.0…

view full answer...

Answer 2

I've attached some pictures showing the size of the ball in the monitor mount of the Voyager RV Observation Camera System w/ Monitor and Mount - 4.3" LCD Monitor Item #VOM43HDCL1B. The ball is a little oblong and the flat portion up top is…

view full answer...

Answer 3

The Voyager RV Backup Camera Monitor #VOM719WP could realistically be mounted in the dash, but you would have to come up with a way to mount it and run the wires yourself since there is no kit or mount designed for this. Typically this is mounted…

view full answer...

Answer 4

Hi Larry, Yes, Voyager has a Universal Monitor Mount that's 4" tall #VOSHD4MNT and 6" tall #VOSHD6MNT. These would screw into the back of the monitor and the base could either be screwed down to the dash or you could use some…

view full answer...

Answer 5

Furrion and RVS camera systems use different mounts so the RVS Extendable Monitor Mount #RVS-1419 will not be compatible with your Furrion monitor. But we do offer a couple of universal-type monitor mounts that may be adapted to work with many…

view full answer...

Answer 6

Hey Gary, yes the part #ASA33YR would work for you as this is the correct replacement mount for the WiSight which is what you have. I wish we had just the nut by itself but at this time we do not.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What Is the Ball Size of the Suction Cup Mounting Bracket for Voyager Wireless Observation System

Continue Researching