Will The SportRack Vista XL SR7018 Fit On My 2024 Subaru Outback Onyx XT?

Question

Question:

Hello, Is the roof rack on my 2024 Subaru Outback Onyx XT compatible with this cargo box? And, once installed, will it interfere with opening the rear lift gate?

asked by: David W

0

Expert Reply:

I do have some information that you should find helpful, but I do not know exactly what roof rack you have on your 2024 Subaru Outback Onyx XT, so I cannot say for sure. What I can tell you is the SportRack Vista XL # SR7018 fits crossbars up to 3-1/8" wide x 1" tall. I recommend measuring the width and height of your crossbars to make sure they don't exceed the requirements. The Vista XL is designed to fit virtually any crossbar brand or shape, including OEM Subaru crossbars.

I also recommend opening your trunk and measuring from the center of the front crossbar in the maximum forward position to the line where the roof and trunk meet. If this length is longer than 39.5 inches, then the box will not interfere with the liftgate.

expert reply by: Jesse M

0

Answer 1

To determine if the SportRack Vista XL cargo box, #SR7018, will fit your Subaru, it will need to have crossbars on the roof that run from side to side. If it does and the crossbars are no larger than 4 inches in diameter and the center to center…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will The SportRack Vista XL SR7018 Fit On My 2024 Subaru Outback Onyx XT?

Continue Researching