Are Any Tools Needed to Install a Sweep Seal on a Pace Edwards Retractable Truck Bed Cover

Question

Question:

What type of tools do I need to replace the sweep seal on my switch blade tonneau cover?

asked by: John

0

Expert Reply:

According to Pace Edwards, you should not need to use any tools to install the Replacement Sweep Seal Roll for Pace Edwards Retractable Hard Tonneau Cover # PE78UV but if need be they mention that you can use an Allen wrench to draw out the seal.

expert reply by: Bryce D

0

Answer 1

For the Pace Edwards Switchblade we do have replacement seals. The Replacement Sweep Seal Roll #PE78UV comes in a 16' length and gets trimmed to fit. This will replace the sweep seals on the side rails for your Switchblade cover. The Replacement…

view full answer...

Answer 2

The Replacement Sweep Seal Roll #PE78UV that you mentioned is for sealing the retractable cover along the sides of your truck bed. This comes as a 16 foot strip that can be trimmed to the necessary length and is specifically made for the following…

view full answer...

Answer 3

The Replacement Sweep Seal Roll #PE78UV is what you're looking for with your Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w Explorer Series Rails #311-FEFA18A44. This seal kit is for where the top rail of the cover meets the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Are Any Tools Needed to Install a Sweep Seal on a Pace Edwards Retractable Truck Bed Cover

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching