Looking for Side Rail Seals for Pace Edwards UltraGroove Tonneau Cover

Question

Question:

I have a Pace Edwards UltraGroove Tonneau cover. I need a replacement for the weather seal adhesive for the side rails on the outer sides. And the adhesive tape on the bottom of the rails as well.

asked by: Luis R

0

Expert Reply:

Hey Luis, is what you are looking for the sweep seal like the part # PE78UV? This is the seal for where the top rail of the cover meets the retractable cover on the sides of the bed.

expert reply by: Jameson C

0

Luis R.

1/14/2026

The outer perimeter weather seal on the railing. Maybe a t- style weather stripping seal?

Jameson C.

1/14/2026

@LuisR Is there a bulb? We have the part # PE92TJ that has a T-slot like you mentioned with a bulb on top of it that works as the seal.

Caleb S.

1/16/2026

I bought the seal for my town cover and it worked excellent installs a little tough, but the seal works great

Armando L.

1/16/2026

I bougth the seal, and it works the the way it should, just prefect

Answer 1

Hey Rick, we do have replacement sweep seal for the Pace retractable tonneau covers with the part #PE78UV. This is a roll that is 16 feet long so it would be enough for a 8 foot long truck bed.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Looking for Side Rail Seals for Pace Edwards UltraGroove Tonneau Cover

Product Page this Question was Asked From

Continue Researching