Is There Plastic Wear Pad Between 1-3/4 Inch Wide Slipper Spring e49SR & Frame

Question

Question:

is there a wear plastic wear pad to go between the spring and traier frame 1/3/4 inch wide for slipper spring

asked by: Richard A

0

Expert Reply:

Nope, there is not any type of plastic wear bad to go between the 1-3/4" wide 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long # e49SR and trailer frame.

expert reply by: Kyle S

0

Answer 1

Hey Chuck, thanks for all of the dimensions you mentioned from your current springs. Based on that the best replacement option we have would be the part #e89SR which is for a 3,700 lb axle, is 1-3/4 inches wide, and overall is 30 inches. Your hanger…

view full answer...

Answer 2

Hey Steven, the closest thing we have would be the part #e49SR which has a 1,450 lb capacity per spring and overall is 30 inches long. The width is 1-3/4 inches as well. Is the 26.5 inch you need the overall length or from the eye center to where the…

view full answer...

Answer 3

The leaf springs should be rated to match the axle on the trailer. Spring #e27SR is rated for 2,250 pounds per spring so it fits 4,500 pound axles. These springs would be overkill for a boat weighing up to 1,900 pounds and it would be a very stiff…

view full answer...

Answer 4

Hey Kevin, welcome back. The CE Smith boat trailer item #CE48810 has a 1.98" inner hub diameter. You'll want the etrailer Bearing Protectors w/ Covers for 1.98" Hub Bore item #e99005. The etrailer item #e99005 are sold as a pair, will…

view full answer...

Answer 5

Hey Jarrod, thanks for reaching out! I believe what you're looking for is the 30" Long 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles #e49SR, although this may be a bit longer than what you currently have. If you take the…

view full answer...

Answer 6

To properly measure your leaf springs you'll want to lift the trailer by the frame to take the weight off of the suspension and then measure from the center of the eyelet straight across the spring to the end of the slipper (pictured below). From…

view full answer...

Answer 7

Yes, the end of a slipper spring like the #e49SR will be very close to the hanger bolt in the unloaded position. There is no exact distance or placement, but it needs to allow for full suspension travel once installed. If the hanger is near the end…

view full answer...

Answer 8

I have a replacement option for you, but the only slipper spring we offer that is 1-3/4" wide and is 26-1/4" long is the 4-Leaf Slipper Spring w/ Open Eye End for 4,300-lb Trailer Axles - 26-1/4" Long #e33SR. Since you mentioned that…

view full answer...

Answer 9

Our trailer leaf springs are rated for dynamic axle load. Which means the capacity listed but in use on the highway under normal circumstances. Since your trailer is 2,200 lbs loaded you want to go for a spring capacity 2,200 lbs or slightly higher.…

view full answer...

Answer 10

What happens to slipper springs is that over time they elongate and flatten out, particularly if your springs are considerably older. The most important measurement you mentioned was the 26 inches from the center of the spring eye to the end of the…

view full answer...

Answer 11

Yes, you could use leaf springs for a 4,000 lb axle, like part #e57SR (rated for 2,000 lbs each), with a 3,500 lb axle but it will make your ride a bit more stiff. The only times that a leaf spring would become damaged is if it is overloaded or has a…

view full answer...

Answer 12

The two closest leaf spring options we have for you are 29-1/2" and 27"long. That said, leaf springs need to be measured unloaded and the exact point will vary by spring type. I would also like to note that leaf springs stretch over time.…

view full answer...

Is There Plastic Wear Pad Between 1-3/4 Inch Wide Slipper Spring e49SR & Frame

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching