Wheel to Mounting Plate Distance for Ultra-Fab Hitch Mounted Steel Rollers for 2-1/2" Hitch Tubing

Question

Question:

What is the overall height of the UF48-979017 from the top of the mounting plate to the bottom of the wheel

asked by: Dave

0

Expert Reply:

You're looking at 3-3/8" from the bottom of the wheel to the top of the mounting plate on the Ultra-Fab Hitch Mounted Steel Rollers for RVs w/ 2-1/2" Hitch Tubing # UF48-979017.

expert reply by: Jon G

0

Wheel to Mounting Plate Distance for Ultra-Fab Hitch Mounted Steel Rollers
(click to enlarge)

Answer 1

If you are going slow in your drive (or anywhere you might suspect is too steep) then using the skid wheels, #UF48-979017, will not damage anything. The damage would come from a sudden hard impact and even then it would have to be a pretty major…

view full answer...

Answer 2

You could mount some skid wheels to the frame by your stabilizers to have them hit first and protect the stabilizers and the rest of the undercarriage from scraping when coming out of a steep incline/decline. I recommend ones like the Ultra-Fab Skid…

view full answer...

Answer 3

Hi Mark; we don't know all of the differences between those different models, and only the #DOM67FR remains available. All of the others have been discontinued. Dometic makes slight changes and upgrades over time but those typically aren't…

view full answer...

Answer 4

In order to choose the correct set of skid wheels you'll need to measure the square body on the trailer hitch and then choose the correct ones based on that. The Ultra-Fab Hitch Mounted Skid Wheels part #UF48-979017 for example are designed for a…

view full answer...

Answer 5

I went out to our warehouse and pulled the Ultra-Fab Skid Wheels for Class C RVs part #UF48-979012 for you. The dimensions of the following components are as follows: The metal mounting brackets are 8-1/2" long X 4-1/2" wide. The two…

view full answer...

Answer 6

I went out to our warehouse to grab a couple measurements on the Ultra-Fab Steel Roller, #UF48-979020. The mounting bracket measures 1-1/4 inches from the center of the hitch pin hole to the edge of the bracket. You will need to determine if the two…

view full answer...

Answer 7

Here are the instructions for Swivel Skid Wheels #UF48-979012 1. Position a board as shown in Illustration 1. Place one end of board just behind rear wheels. Prop up the other end of board so board comes in contact with the lowest point of RV’s rear…

view full answer...

Answer 8

I went out into our warehouse and pulled a set of the Ultra-Fab Rotating, Hitch Mounted Skid Wheels #UF48-979014 and found that the distance from the bottom of the wheel to where the bottom plate will be is 5-3/4 inches. Since the bumper you plan to…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...