Recommended Replacement Braking Assemblies for a 2018 Coyote Trailer W/ 3.5K Axles

Question

Question:

Looking for brakes and bearing kit for 2018 coyote trailer with two 3500lb axles with torsion spring.

asked by: Patrick

0

Expert Reply:

For 3,500 lb axles, you can use the Electric Trailer Brake Kit # AKEBRK-35-SA to replace your brakes, however for your bearings you are going to need to actually pull off the bearings you're needing to replace and look for the number stamped on it; i.e. L68149 or L44649.

I've attached a FAQ that goes into a bit more detail when it comes to finding the correct bearings.

expert reply by: Bryce D

0

Answer 1

We do have some options for replacing the Knott calipers and rotors on your Coyote Boat Trailer. We really do not have any info or specs on the Knott brand brakes, but since it is all for a 3,500 lb axle the sizing should be standard. Standard…

view full answer...

Answer 2

Hey Dwyane yes that is necessary unfortunately. We do have disc brake kits like the DeeMaxx Disc Brake Kit #DE68YR which will work with 7,000 lb axles that uses specific bearings. The last couple of things you'd need is a brake line kit…

view full answer...

Answer 3

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Recommended Replacement Braking Assemblies for a 2018 Coyote Trailer W/ 3.5K Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching