Most Concealed Hitch for a 2016 Subaru Legacy Outback

Question

Question:

I have a 2016 Subaru Legacy. I would like to add a hitch to my vehicle that doesn't stick out as much or hang down below. Is this an option?

asked by: Jeff B

0

Expert Reply:

Yes, it is. To add a hitch to your 2016 Subaru Legacy, I recommend the EcoHitch Hidden Trailer Hitch item # 306-X7271. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class II hitch with a 2" receiver.

I really like this hitch because it mounts behind the rear bumper cover leaving only the 2" receiver exposed. This not only looks better but also helps with ground clearance.

I have attached a picture below so you can see what this hitch looks like when installed.

If you are planning on towing you will also need a wiring harness item # C56246 and a ball mount kit item # C45534.

I also recommend using the No-Drill Mount Bracket item # 18136 and the item # C42CR to secure the 4-way connector to your hitch. This will put it in an easy to reach spot and prevent the risk of it falling onto the road.

expert reply by: Jerred H

0

EcoHitch Hidden Trailer Hitch
(click to enlarge)

Answer 1

Realistically that would probably be fine, but since we know Curt won't honor the warranty unless it's ran directly to the battery we can't recommend you go about the install in any other way. If you can find a safer way to run the power…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Most Concealed Hitch for a 2016 Subaru Legacy Outback

Products Featured in This Question

Continue Researching