Installation Diagram for the Replacement Reese 5th Wheel Spring part # 30776

Question

Question:

We received our replacement spring 30776 we are putting it on a 20K Reese fifth wheel hitch are the instructions and diagrams the same as a 16K?

asked by: John

0

Expert Reply:

Yes, the diagram and installation instructions for the Replacement Spring for Reese and Draw-Tite Fifth Wheel Trailer Hitches # 30776 are the same between a 20k and a 16k Reese Fifth Wheel Hitch.

I attached the diagram for this spring to show you how and where it would install.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Resetting the #FR33PR requires pulling the power from the thermostat. However, it is unlikely this will fix your error code. The E3 code means there is a loss of communication between the thermostat and control box. Double check your wires and make…

view full answer...

Answer 2

Usually, these springs should not have to be replaced unless they are damaged. You will want to check the Reese Replacement Spring, #30776, and make sure it is not damaged and check the Reese 16K Fifth Wheel Hitch, #RP30047, to make sure that there…

view full answer...

Answer 3

I attached the correct diagram for spring replacement in your Reese 15k Fifth wheel hitch that is now part #RP30047. I attached a pic of the head of your system and you will see the diagonal spring across the hitch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Installation Diagram for the Replacement Reese 5th Wheel Spring part # 30776

Continue Researching