Class III Draw Tite Hitch that Fits 1989 Chevy K1500 with 37 inch Frame

Question

Question:

Need hitch for 1989 Chevy K1500 Frame rails 37 outside to outside Has step bumper that protrudes 2 below frame rails. Class 3 or 4. Unable to determine from your listings. Help.

asked by: Lloyd B

0

Expert Reply:

The Draw Tite Class III hitch part # 75033 that you referenced does fit your 1989 Chevy K1500 with the 37 inch frame dimension and step bumper.

expert reply by: Jameson C

0

Answer 1

The main difference between Draw-Tite trailer hitches #75033 and #75099 is the placement of the receiver tube on the cross member. On 75033 the receiver is attached to the rear part of the cross member. On 75099 it is welded below the cross member so…

view full answer...

Answer 2

Yes, once you complete the install of the Draw Tite hitch part #36501 on your 2009 Ford Escape you will be able to reinstall the spare tire. I attached a picture that shows the spare reinstalled for you to check out as well.

view full answer...

Answer 3

The HappiJac Qwik-Load Upgrade Kit for Standard Turnbuckles part #LC182894 is an excellent upgrade option for the HappiJac Original Turnbuckles for Camper Tie-Downs part #LC182898. These are going to cut down dramatically on the time it takes to…

view full answer...

Answer 4

According to my contact over at Lippert, when you attempt to clamp down the HappiJac Qwik-Load Turnbuckle #LC182897 if the spring has spring or is weak the buckles will turn a lot easier than one that is fully operational. If you've got one…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Class III Draw Tite Hitch that Fits 1989 Chevy K1500 with 37 inch Frame

Continue Researching