Availability Of a 3.19" Wheel Center Cap To Match Gunmetal Finish On Condor Aluminum Wheels

Question

Question:

Is there a center cap that would match the 15” Condor aluminum wheels in Gunmetal? Preferably not chrome.

asked by: Greg L

0

Expert Reply:

The Black Center Cap # CXF106B is the only colored center cap we currently carry. For the best look I recommend having the Stainless Cap # LHCS102-SI60C dip coated at a local finisher. This would provide a much stronger coating than regular paint.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hello Kevin, Thanks for writing in. The main difference between the Power Watchdog Surge Protectors #HU67FR and #HU42VR comes down to the monitoring capability, housing design, and surge protection rating. The #HU67FR is the newer Generation 2 model.…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

Hey Jascha, yes you can easily change the Kodiak disc brake kit part #KOD53FR to being an oil bath setup by just swapping out the seal to the part #9103309. What's really interesting about the part #KOD53FR is that it actually has oil bath type…

view full answer...

Answer 10

Hi Lee, cool camper! For 2,200 pound axles, you are going to want the Lippert Complete Bearing Kit for 2,200-lb Trailer Axles - L44649 Bearings, L44610 Races #LC23ZP. This includes the bearings, races, seal, cotter pin, and tang washer. It will be…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 12

Welcome back Jordan! I have an alternative for you but we do not have any Ram 7k jacks that can be bolted on. Just welded like item #TJD-7000S and pipe mount like item #TJDP-7000S-B options. For a 7,000 lbs capacity square jack that can be bolted on,…

view full answer...

Availability Of a 3.19" Wheel Center Cap To Match Gunmetal Finish On Condor Aluminum Wheels

Products Featured in This Question

Continue Researching