Determining the Best Top and Side Trim Options for an Enclosed Trailer

Question

Question:

I need trim for the top and sides of this horse trailer.. do you have any recommendations?

asked by: Megan V

0

Expert Reply:

There isn't really a right or wrong answer when it comes to selecting trim for the tops and sides of your trailer. It is really just about selecting the best shape/style/size that fits your contours the best. Trim like the Top Rail Trim for Enclosed Trailer # 362530-955 is made of aluminum. This means you can cut it to size and even carefully conform it to the shapes of you trailer.

The Top Rail Trim for Enclosed Trailer # 362530-955 is a pretty flat trim piece, meaning it is going to do a good job on straight lines/edges. If you are wanting/needing something that wraps around edges/corners like the roof line, something like the Top Rail Trim for Enclosed Trailer # 36279-955 would make more sense.

I have linked our selection of trim. The trim pieces can be secured with screws that you can source from your local home improvement store.

expert reply by: Scott S

0

Back of an enclosed trailer
(click to enlarge)

Side of an enclosed trailer
(click to enlarge)

Answer 1

The TremPro 644 Silicone Sealant #0160297 that you referenced is an ideal product for repairing leaks in a trailer roof. This silicone product remains flexible after it cures and will stick to almost any material likely to be found on a trailer roof.…

view full answer...

Answer 2

We do carry a variety of different trim and edging. Unfortunately we do not have a way to look up a model of trailer to know exactly what kind of trim you will need. We would want to try to match the current trim as best we can. A very common roof…

view full answer...

Answer 3

In order to re-seal the panels on your trailer you can use the TremPro 644 Silicone Sealant part #0160297 as an alternative to the Loctite Urethane Sealant part L0150811. The TremPro 644 Silicone Sealant has a similar compound to the Loctite Urethane…

view full answer...

Answer 4

We have the Nosing Edge Trim #362555-955 which is 1" wide with a 3/16" edge lip. The trim is 93-1/2" long and has an aluminum construction. Since it is aluminum it will bend fairly easily.

view full answer...

Answer 5

My contact at Redline told me that the outside diameter of the Chrome Trim #SA1012ET would be right at 5/16 of an inch and the inner diameter 1/8 of an inch. He said the trim isn't a perfect circle so the dimensions fluctuate a little bit.…

view full answer...

Answer 6

We do have a grease seal that is almost exactly what you measured that should work for you, with the outer diameter being 0.06 inches off, which could very easily be explained by the amount of pressure put on the caliper. So it is very likely that…

view full answer...

Answer 7

The lights inside of the trailer most likely run to a trailer battery and aren't getting power from the 7-way connection to the tow vehicle. To confirm you'll need to unmount the light and trace the wires back to their source. There would…

view full answer...

Answer 8

If the motor on your Husky Electric Trailer Jack HT87247 works when lowering but cannot raise there are a couple of possibilities. The power supply feeding the jack may not be sufficient for the load; the 12v feed on a vehicle 7-way may not be…

view full answer...

Answer 9

If you are replacing your tub and shower diverter faucet you need to measure the center-to-center length of your connections as well as know what type you have. For example if you take a look at the accompanying photo you can see the Ultra Faucets…

view full answer...

Answer 10

Even though you have a 2 inch tall frame to weld a pipe mount to the 3 inch pipe mount that comes with the Bulldog Jack #BD190758 will still attach securely enough to it. You'll just need to have it welded around the mount where it touches the…

view full answer...

Answer 11

Most pintle hooks use a standard bolt pattern which is 3-3/8" horizontally center to center and 1-3/4" vertically center to center (see photo). Therefore, the Pintle Hook part #C48231 would be a direct fit and work well for you. It also…

view full answer...

Answer 12

You are correct that the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 you were looking at is the replacement master cylinder for your older 23361. I included a video of the Titan #T4395100 for…

view full answer...

Determining the Best Top and Side Trim Options for an Enclosed Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching