Replacement Trim For a 1970 Horse Trailer With 1" Wide by 1/8" Lip

Question

Question:

Im trying to replace the outside trim on a 1970 horse trailer but looking for size 1inch with 1/8 lip not sure on length, yet do you carry it. also how hard is it to bend.

asked by: Diana M

0

Expert Reply:

We have the Nosing Edge Trim # 362555-955 which is 1" wide with a 3/16" edge lip. The trim is 93-1/2" long and has an aluminum construction. Since it is aluminum it will bend fairly easily.

expert reply by: Bud M

0

Answer 1

We do carry a variety of different trim and edging. Unfortunately we do not have a way to look up a model of trailer to know exactly what kind of trim you will need. We would want to try to match the current trim as best we can. A very common roof…

view full answer...

Answer 2

My contact at Redline told me that the outside diameter of the Chrome Trim #SA1012ET would be right at 5/16 of an inch and the inner diameter 1/8 of an inch. He said the trim isn't a perfect circle so the dimensions fluctuate a little bit.…

view full answer...

Answer 3

There isn't really a right or wrong answer when it comes to selecting trim for the tops and sides of your trailer. It is really just about selecting the best shape/style/size that fits your contours the best. Trim like the Top Rail Trim for…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 6

Hey Jeff, thanks for reaching out. I just went out to our warehouse and measured the P&F Products J-Channel Rail for Enclosed Trailers #PF26FR. The interior dimension of the J-channel I measured at 0.17". What thickness plexiglass were you…

view full answer...

Answer 7

In regards to the Nosing Edge Trim part #362555-955, the overall depth at the deepest point is 3/16" thick. I have attached a photo below to help clarify.

view full answer...

Answer 8

Hey Steve! The closest piece of trim we have to what you described is the Nosing Edge Trim for Enclosed Trailer item #362556-955. It measures 93-1/2" long x 1-1/4" tall and has a 3/16" lip on it. I do not have a database that will show…

view full answer...

Answer 9

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 10

Hey Bill, thanks for reaching out. The best replacement for your Dexter 013-143-03 Equalizers are the Dexter E-Z Flex #K71-652-00. This is identical in size to the current equalizer so it will be an exact replacement. This kit comes with new wet…

view full answer...

Answer 11

The Nosing Edge Trim #362555-955 is made of aluminum and can be bent fairly easily.

view full answer...

Answer 12

Thanks for the Picture. What you have there is a 6 on 5-1/2" hub for a 3,500 lb axle. We do have a replacement hub for your Truryde RVD-H-65535 hub. The correct replacement will be part #AKHD-655-35-EZ-K. This will include the hub, bearings,…

view full answer...

Replacement Trim For a 1970 Horse Trailer With 1" Wide by 1/8" Lip

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching