What Size Wire Is Needed to Connect the Furrion Chill Single Zone Controller to DC Power

Question

Question:

What gauge wire needs to go from the RV 12V DC power to this unit? What gauge wire needs to go from the controller to the thermostat?

asked by: Brandon M

0

Expert Reply:

You're going to need a minimum of 12AWG wire for the Replacement Single Zone Controller for Furrion Chill RV Air Conditioner Setup w/ 2 Fan Speeds # FR86NR.

To connect it to the thermostat, you'll just need to connect the 4 wires labeled "to wall thermostat" and you'll be set. I've also included a wiring diagram for you to check out as well.

expert reply by: Bryce D

0

Wiring Diagram
(click to enlarge)

To Wall Thermostat
(click to enlarge)

Answer 1

Yes, you can use the Furrion LED distribution box part #FACT12LA-PS with the Furrion Chill RV AC unit part #FR42PV.

view full answer...

Answer 2

You will need to identify your current controller to see if the Replacement Premium Wall Thermostat for Furrion Chill HE RV Air Conditioner #FR33PR is compatible. The model number should be on the controller. According to Furrion, if you have the…

view full answer...

Answer 3

Hey Steve, Yes, the Replacement Premium Wall Thermostat #FR33PR will indeed control the LED lights of the Air Distribution Box for Furrion Chill RV Air Conditioners #FACT12LA-PS.

view full answer...

Answer 4

The air box that comes with the Furrion Chill Premium RV AC unit part #F14PA12SASA-W is the part #FACT12SA-PS which does not have the LED light strip. The air distribution box that does have the LED strip is the part #FACT12LA-PS.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

What Size Wire Is Needed to Connect the Furrion Chill Single Zone Controller to DC Power

Product Page this Question was Asked From

Continue Researching