Bearing Kit for 5,200 lb Trailer Axle

Question

Question:

Hello, I have a 2006 Cam Superline Dump Trailer. 5200 lb axles. Im not sure which bearing kit I need.

asked by: Colleen D

0

Expert Reply:

For your 5,200 lb trailer axle the correct bearing kit would be the part # BK3-300 for if the grease seal spindle diameter is 2.25 inch or part # BK3-310 if it is 2.125 inch. It's pretty random which seal diameter is used so you'd have to measure you spindle.

expert reply by: Jameson C

0

Answer 1

Hi John; that is definitely the kind of thing you don't want to find but at least you can take care of it now. Once you get everything cleaned up you can swap over to the etrailer Electric Trailer Brakes - Self-Adjusting #AKEBRK-7-SA without any…

view full answer...

Answer 2

Bearing Buddies are a great way to keep grease in a trailer hub. I recommend them as long as you are aware that it's very easy to put too much grease in a hub with these which will blow out the seal. They have no problem being used on longer road…

view full answer...

Answer 3

When you use the Bearing Buddy Bearing Protectors like #BB2441, so you do not need to take apart the wheel hub and repack the bearings. The Bearing Buddy Protectors have a spring loaded seal that keeps the moisture and debris out of the bearings.…

view full answer...

Answer 4

For your Dexter 5,200 lb hub the Bearing Buddy part #BB2441SS is the correct fit. Installing it is pretty easy. Using a flat board and a mallet you'd lightly hammer it into place.

view full answer...

Answer 5

Believe it or not, the outside diameter of the Bearing Buddy is designed to be a bit larger than the inside diameter of the hub bore. Typically, a Bearing Buddy sized to fit a 1.98 hub bore will actually be about 1.986 in diameter, which means yours…

view full answer...

Answer 6

Our video team has included the hole spacing measurements at the end of the video I have linked for you. The holes on the short side are spaced 4 inches apart on center and on the long side they are spaced 6-1/4 inches apart on center. The holes are…

view full answer...

Answer 7

Best solution we have would be a weld on hitch tube like the part #337RT255808 which is the correct 2-1/2 inch hitch size. You'd need to have this welded onto your trailer frame in a location that makes sense but we don't have a custom…

view full answer...

Answer 8

The Bulldog Winch Hitch Mount Storage Bracket #BDW20154 that you referenced comes with bolts for installing it but yes, 1/2 inch diameter bolts would also fit the slots.

view full answer...

Answer 9

I have a recommendation for you as the Bulldog Winch Hitch Mount Storage Bracket #BDW20154 is only designed to hold a winch when not in use. It does not have the structure required to operate a winch. For a 12,000LB Winch #BDW10040 you will need a…

view full answer...

Answer 10

It does! I did some research and found out the Warn Zeon 12 winch has the standard 10" x 4.5" bolt pattern, which is exactly what the Bulldog Winch mounting plate has. So yes, the two are compatible, and the part number for the hitch…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Bearing Kit for 5,200 lb Trailer Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching