Replacement Recommendation for a High Pointe EM925RYS Model Microwave

Question

Question:

need replacement microwave for high pointe model number EM925RYS. would you have a replacement ?

asked by: Mark S

0

Expert Reply:

According to my research it looks like your current High Pointe microwave measures 19.1 x 14.8 x 11.3 so for a replacement I recommend the following:

- High Pointe Standard RV Microwave w/ Trim Kit - Stainless Steel # HP59ZR

This is rated for 900W like your current microwave and it also measures 19-1/8" wide x 11-1/2" tall x 14-13/16" deep so it should be pretty comparable to the microwave you have now.

expert reply by: Jon G

0

Answer 1

Yes, the High Pointe Direct Replacement EM925AQR, which is part #HP59ZR on our site, will replace your existing microwave High Point model number EM925RYS.

view full answer...

Answer 2

You can select your new hubs by matching up your axle weight rating, wheel bolt pattern and the bearings used in your current hubs. Based on my research your hubs are 10 x 2-1/4-inches, are from a 3500-lb axle and have the 5-on-4-1/2 bolt pattern. If…

view full answer...

Answer 3

The correct seal for a Dometic 300 Series Toilet 302300093 is the Replacement Toilet Base Seal for Dometic RV Toilet part #DOM28FR.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Recommendation for a High Pointe EM925RYS Model Microwave

Featured Help Information

Miscellaneous Media

Continue Researching