Installing Redarc Tow-Pro Liberty on 2024 Chevrolet Silverado 2500 With Tow Package

Question

Question:

I would like to add this redarc liberty to a 2024 Silverado 2500. It has the tow package with that port underneath. Is there a way to make this work so it is plug and play?

asked by: Tyler

0

Expert Reply:

Yes, there is a way to make this work so you can plug the brake controller into the port under the dash on your 2024 Silverado 2500. Curt has the # C51525 wiring harness which is compatible with your truck. This wiring harness, along with the # 331-TPH-019 adapter, will allow you to install the # RED24FR without having to splice any wires.

expert reply by: Robin H

0

Answer 1

To install either the Redarc Liberty #RED24FR or Elite #RED44FR on your 2024 Chevrolet Silverado 1500 you will need the Wiring Adapters #3064-P and #331-TPH-017. These will allow you to plug into the factory tow package wiring.

view full answer...

Answer 2

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 3

For your 2024 Chevy Silverado 1500 I recommend the Redarc Tow Pro Elite #RED63RR. You can use it along with the Plug in Adapter #3064-P for a plug and play install, since you already have the factory tow package. The Redarc controller is going to be…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...