Correct Replacement for a 010-019-00 Grease Seal

Question

Question:

Grease Seal Recommendation for Dexter 4,400 lb Trailer Hub, the part# for the Seal from Dexter is 010-019-00.

asked by: Steven W

0

Expert Reply:

The correct replacement grease seal for your Dexter hub is the Grease Seal # RG06-050. This has been cross referenced and confirmed to be the correct replacement.

expert reply by: Bryce D

0

Answer 1

The hub your Shorelandr boat trailer has is part number 4470400 which is a 3,500 lb axle hub. So for a replacement surge brake assembly you'd want the part #AKUBRK-35 for a set of left and right hand assemblies.

view full answer...

Answer 2

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Answer 3

The correct bearing kit for a Dexter 4,400 lbs axle is item #BK2-100. The Dexter 4,400 lbs axles use the same bearings and seals as a Lippert 3,500 lbs axles. This kit includes inner bearing item #L68149, inner race item #L68111, outer bearing item…

view full answer...

Answer 4

Hi Gary; we have previously confirmed that the #DMC46FR will fit the Dometic 57915.751E0 so the cover you found for your Brisk Air is correct.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hello Andrew. I had a cotter pin for an ez-lube spindle part #165649 laying here on my desk so I grabbed a micrometer to measure. With both halves of the pin pressed together is measures 0.11". Each half of the pin is like 0.05". I edited a…

view full answer...

Answer 9

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 10

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Correct Replacement for a 010-019-00 Grease Seal

Product Page this Question was Asked From

Continue Researching