Bearings For 15/16 Inch Outer Diameter Spindle

Question

Question:

My spindle measures 15/16 OD- what would be my bearing size ?

asked by: Vinston A

0

Expert Reply:

A measurement of 15/16" equals 0.938" and the bearing with a 0.938" inner diameter is the following:

- Trailer Hub Bearing # 1779

expert reply by: Kyle S

0

Answer 1

Based on the axle and bearing measurements it looks like your trailer was using a Dexter 22834 hub. The Outer Bearing #1779 has an ID of .938" and the Inner Bearing #2788 has an ID of 1.50". The outer bearing is slightly off but that may be…

view full answer...

Answer 2

It sounds like you have a pretty nice trip planned! Bias trailer tires do not have a set range you can travel as they meet DOT standards for a tire. With that said before you start your trip I would make sure to check your tires for any dry rot or…

view full answer...

Answer 3

What I would recommend you do is extract as much of the old zerk fitting as you can and then going forward grease that hub by hand and you'll be totally fine if not better off than using the grease fittings. It's pretty easy to overfill EZ…

view full answer...

Answer 4

The hub you are looking for is the part #AKIHUB-440-2-EZ-2K which is a pre-greased idler hub with a 4 on 4 inch bolt pattern that has both bearings with an inner diameter of 1.06 (1-1/16) inch like you need.

view full answer...

Answer 5

I have a way to help you find out what replacement hub assembly you need, but you'll need to verify some things on your end as I don't have a list of replacement parts for your trailer available. Since your 1992 Ranger Trail is a tandem axle…

view full answer...

Answer 6

When measuring for bolt pattern on an even bolt pattern you would measure from the center of one hole to the center of the hole diagonally across from it. In your picture you started measuring at the 1 inch mark. So if the adjacent measurement is…

view full answer...

Answer 7

If you are looking to order a new axle for your 5 foot wide trailer you will need to determine what the hub face to hub face dimension you would need to clear your trailer that is 5 feet (60 inches) wide. You will also need to know the width of your…

view full answer...

Answer 8

Thanks for all of the info! It looks like you have a BT8 spindle so that's the type of replacement hubs you need. This style is available with a 4-bolt or 5-bolt pattern so I'll give my recommendations for each: - 4 on 4" Bolt Pattern…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Bearings For 15/16 Inch Outer Diameter Spindle

Product Page this Question was Asked From

Continue Researching