How is Different Spring Bar Tension Accomplished with the Reese Weight Distribution RE34FR

Question

Question:

The video suggests that the WD system can be adjusted according to the actual tongue weight. How is this done?

asked by: Clif B

0

Expert Reply:

Using a different amount of washers in the head of the Reese weight distribution system part # RE34FR will allow you to adjust how much spring bar tension is used. The more washers are used the further down the bars will point and the more amount of force would be required to get them onto the mounts.

expert reply by: Jameson C

0

Answer 1

Pertaining to the Reese Pro Round Bar Weight Distribution Hitch #RE34FR, the head itself without a ball is about 20 lbs. The shank is about 25 lbs. The ball itself would be 3 lbs. Each spring bar is about 12 lbs apiece.

view full answer...

Answer 2

If the rear end of your vehicle sags significantly when the trailer is hooked up then you could have an unsafe condition and your front end and tires will not wear properly. The weight is taken off of the front wheels of the vehicle and can cause…

view full answer...

Answer 3

Thanks so much for that good information, and we can get you exactly what you are looking for - a quiet weight distribution hitch that is rated correctly for your 465 lb tongue weight and provides outstanding sway control. For that the best option is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Michelle! There are definitely a lot of different weight distribution hitch (WDH) options out there. The most important thing is to make sure it is properly rated for the tongue weight of your setup. Looking at the specs for the 2022 Keystone…

view full answer...

Answer 6

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Answer 7

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 8

Hi Chandler! I see you already placed an order, but I still wanted to get you an answer to your question. The Equal-i-zer Weight Dist Shank - 12" Long - 7" Rise, 3" Drop - 600 to 1,400 lbs TW #EQ90-02-4100 is for a 2" hitch. The…

view full answer...

Answer 9

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 10

Hey Frank. I can give you the dimensions of the shank on the B&W Continuum item #BW28FR but you're going to need to take the measurements on your Silverado 3500 to confirm the tailgate will open. From the hitch pin hole to the center of the…

view full answer...

Answer 11

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 12

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

How is Different Spring Bar Tension Accomplished with the Reese Weight Distribution RE34FR

Continue Researching