Does Yakima FrontLoader Bike Rack Fit on Thule Square Crossbars

Question

Question:

Will the Yakima front loader fit on Thule square bars?

asked by: Kurt F

0

Expert Reply:

Yep, the Yakima FrontLoader bike rack part # Y02103 does fit on Thule square crossbars.

expert reply by: Jameson C

0

Answer 1

Hey Thomas, with the SumoSpring part #SS65GR you do want to have the front and rear installed on the springs even though only the rear seems to be making contact as is. You want uniform pressure on the front and back otherwise it will just flex…

view full answer...

Answer 2

The Yakima FrontLoader bike rack, #Y02103, will fit crossbars that are up to 4 inches wide so it will fit the Thule AeroBlade crossbars. The center to center distance between the bars will need to be 16 to 48 inches. I have linked a video review of…

view full answer...

Answer 3

The cradle measures 11 x 3 inches, the upright arm is 17-1/2 inches tall and the arm is 6-1/2 inches wide. It's constructed of 1 inch tubing with the padded portions being right at 1-1/2 inches in diameter. The arm locks flat, at 90 degrees and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Greg! The etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers #e55YV is not compatible with a weight distribution hitch. This is really the only restriction for our anti-rattle. If you need an anti-rattle for a weight distribution…

view full answer...

Answer 12

Hey Charles! The Curt TruTrack 2P Trunnion Weight Distribution System w/ Sway Control - 7-Hole Shank - 12K GTW #C75RJ will work great with your 2026 F-250 to pull a 25-30 ft RV. There isn't a kit with a 2.5" shank, but you can add Curt…

view full answer...

Does Yakima FrontLoader Bike Rack Fit on Thule Square Crossbars

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching