Wiring Needed To Install Hayes Engage 81760 Trailer Brake Controller on 2023 Ram 1500

Question

Question:

What is the part number for the wiring harness adapter for a 2023 Ram 1500? Hayes 81760 controller.

asked by: Eldon J

0

Expert Reply:

You will need the Curt Custom Wiring Adapter # C51458 for your 2023 Ram 1500. This will allow you to connect your Hayes Engage Trailer Brake Controller # HA81760 to the factory connector under the dash.

expert reply by: Bud M

0

Answer 1

Hello John, thanks for reaching out. We do carry parts for the Equalizer weight distribution hitches, and we actually have exactly the part you are looking for. What you will need is the Inner Link Plate #EQ90-02-5210 and outer link plate…

view full answer...

Answer 2

I recommend selecting one of our Equal-i-zer weight distribution hitches. Equal-i-zer has earned the reputation of being one of the best systems available with their excellent quality and durability to last. You will need to select one of the hitch…

view full answer...

Answer 3

If you are getting persistent sway at 65 mph a weight distribution system will not be the correct solution. You most likely either have not enough tongue weight or a worn out suspension component that is causing the sway. Does it seem to be any…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 11

Hi there Chris, great question. Yes the Redarc #RED87CR is truly a plug and play brake controller for your 2026 Ram 1500. It connects directly to the factory tow controller connector under the dash, so there’s no dealer programming required like you…

view full answer...

Answer 12

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Wiring Needed To Install Hayes Engage 81760 Trailer Brake Controller on 2023 Ram 1500

Products Featured in This Question

Continue Researching