Does Fusion GloLight Tail Light part # OPT64WR Require Resistor

Question

Question:

I have a question regarding part #OPT64WR 4 inch led tail light. Do the lights have integrated resistors for turn signals or do I need to buy them separately? Thanks,

asked by: Dean

1

Helpful Expert Reply:

Since the Fusion GloLight Tail Light part # OPT64WR is designed to be a trailer light and not a vehicle light it does not have any resistors integrated into it. Trailer wiring does not require this because the signal comes from the vehicle wiring which already has the flasher unit functioning. If the light was to be installed on a vehicle in place of a blinker circuit a resistor would be needed or a digital flasher installed on the vehicle instead of a thermal unit.

The proper resistor value would be based on the type of light bulb it was replacing which you'd have to google for.

expert reply by: Jameson C

1

Answer 1

Hi Christopher; thanks for the question though Fusion GloLight Combination Tail Light #OPT64WR does not come with a clear lens. This light is only made with the red and clear lens combo.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

The best and easiest way to install a round 4" tail light like the Miro-Flex LED Trailer Stop/Turn/Tail Light part #STL23RB on a trailer would be to first clean the edges of the holes (no sharp metal) and then spray some soapy water on the…

view full answer...

Answer 8

Hey Brian, if you grab the magnet and move it in the direction of the arm that it is attached to far enough it will click and it will adjust the star wheel tighter. This will be the easiest way to move the shoes out. Or you can install them and then…

view full answer...

Answer 9

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 10

Hello Kirsten, thanks for reaching out. Unfortunately, we do not offer a trailer jack with a 1-3/4" outer tube diameter. There used to be a jack from Bulldog that had a 1-3/4" tube diameter, but it has been unavailable for quite some time.…

view full answer...

Answer 11

I would start by checking location 74 which is the relay for the trailer tow left-hand stop/turn function. Another place to check is location 100 which is the trailer tow turn signal function. You could also check location 70 which is the trailer tow…

view full answer...

Answer 12

You have done a great job troubleshooting the problem so far and have isolated the issue to the truck wiring. I have confirmed with my contact at Tekonsha, and another fuse that you might check would be fuse #6 in the under dash junction box. This is…

view full answer...

Does Fusion GloLight Tail Light part # OPT64WR Require Resistor

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching