Who Manufactures etrailer Round/Wheeled Swivel Jack

Question

Question:

MJ-1500B-DWL 1500 # Trailer, who is manufacturer and country of manufacture? Thank you

asked by: Marvin T

0

Expert Reply:

The # MJ-1500B-DWL is made in China. If you're looking for a USA made alternative I recommend the Dutton-Lainson # DL22580. This has a 12" lift, the same 1,500 lb capacity, and dual wheels. It uses a bolt-on installation and fits square tongues up to 3" x 5".

expert reply by: Robin H

0

Answer 1

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 2

I spoke to my contact at Dutton Lainson to get the dimensions you requested. The overall height of the jack when fully retracted is 26-1/2 inches. It measures 14-1/2 inches from the center of the bracket to the bottom of the jack wheel. It measures…

view full answer...

Answer 3

While we do have some great U.S.A.-made boat trailer jacks, the etrailer Round Swivel Marine Jack #MJ-1500B-DWL is manufactured in China. However, for a super close U.S.A.-made model, I recommend the Dutton-Lainson Swivel Marine Jack #DL67MR. This…

view full answer...

Answer 4

Hey Bruce! I'm not too sure what you're looking for, but I see that you were looking at trailer jack's so I'll assume that's what you're referring to. If this is the case, the etrailer Boat Trailer Jack w/ 2 Wheels…

view full answer...

Answer 5

Hey Brian, the replacement I recommend for an Atwood Surge Brake Actuator 85778 is the Demco Hydraulic Brake Actuator part #DM62VR. It has the same ball size, offers a bolt-on install, and has a greater capacity. The only difference is it has an…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Who Manufactures etrailer Round/Wheeled Swivel Jack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching