What Would Cause Rear Tires of Tandem Axle Trailer to Wear Out in Middle

Question

Question:

I have a 2019 Springdale 26ft dual axle Rv travel trailer with around 3000 miles towed. The tires on the rear axle a worn almost smooth on the inside. I’m wondering what’s some probable causes?

asked by: Troy N

0

Expert Reply:

That sounds like the trailer is being towed nose high which is putting too much weight on the rear axle and wearing out the tires of it.

expert reply by: Jameson C

0

Answer 1

Excessive tire wear on just one tire of a tandem axle trailer could indicate a few things. First, and the easiest to check, it could be a problem with some component of the suspension. You will want to inspect the suspension on that side and look for…

view full answer...

Answer 2

The most general causes of a tire wearing on one side faster than the others could be as simple as inflation not being consistent across both side, front to back and side to side or it could be a bit more involved such as a bent spindle. I recommend…

view full answer...

Answer 3

You can figure exactly where to position your axles as well as the wheel base by simply plugging some numbers into the handy chart I've added for you. This will tell you where the axles need to go and thus, what the wheel base will be. I have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

The equalizers that come with the Dexter Heavy-Duty Suspension Kit #K71-448-00 have bolt holes that measure 6" apart on center and then 4" tall on center as you can see in the attached photo. You'll want to measure your current…

view full answer...

Answer 11

Hey Eric. Axle spacing isn't the best way to determine what replacement equalizers you need. The most accurate way to find a replacement is to match up a replacing equalizer as close as possible to the dimensions of the one currently on your…

view full answer...

Answer 12

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

What Would Cause Rear Tires of Tandem Axle Trailer to Wear Out in Middle

Product Page this Question was Asked From

Continue Researching