Can the J-Channel Trim for Enclosed Trailers Be Bent to Fit a Vintage Camper

Question

Question:

Will I be able to bend this J-channel trim gutter for my vintage camper?

asked by: Jakob

0

Expert Reply:

The J-Channel Trim for Enclosed Trailer # 362416-955 is made of aluminum, which is a soft metal and can be bent or conformed to a different shape. It can also be cut/trimmed. If you need to make any sharp bends in the trim, heating up the area that will be bent would be a good idea.

expert reply by: Scott S

0

Answer 1

I don't think anyone really wants to replace their coupler when the latching mechanism is bad or worn but, it's unfortunately a must since they don't make universal trailer coupler repair kits. There are trailer coupler repair kits…

view full answer...

Answer 2

In order to re-seal the panels on your trailer you can use the TremPro 644 Silicone Sealant part #0160297 as an alternative to the Loctite Urethane Sealant part L0150811. The TremPro 644 Silicone Sealant has a similar compound to the Loctite Urethane…

view full answer...

Answer 3

The groove inside the J-Channel Trim for Enclosed Trailer #362415-955 measures 3/16" wide x 1/8" tall with the trim laying flat so that should give you a good idea what kind of diamond plate will fit.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can the J-Channel Trim for Enclosed Trailers Be Bent to Fit a Vintage Camper

Product Page this Question was Asked From

Continue Researching